Nady Systems X2 operating instructions Specification, Service, Handheld MIC Transmitter

OPERATION

(11) (10) (9) (8)

HANDHELD MIC TRANSMITTER

1.Unscrew the BATTERY COMPARTMENT COVER (6) and remove. Insert a fresh alkaline 9V BATTERY (9), observing correct polarity as marked, and screw the cover back on to the microphone. To ensure proper battery contact, the cover must be screwed on completely

2.Turn on the handheld mic by sliding the OFF/STANDBY/ON (10) switch to the ON position. The BATTERY INDICATOR LED (11) will light up continuously, indicating usable battery strength. In the case of a dead or low battery, the LED will either light dim or not light at all, indicating that the battery should be replaced with a fresh one

3.The microphone is now ready to use. The corresponding LED INDICATORS (7) on the American Starpower™ X2 receiver should now be lit, indicating a received signal from the transmitter on that channel.

4.The two channels are labeled red and blue, both on the front panel of the receiver and on the band label on the microphone just under the mic ball grill. This color coding enables visual display of which transmitter is turned on and transmitting to the receiver. Both channels can be used simultaneously and this is the preferred method of operation. Single channel operation is also possible. Occasionally, depending on the radio signal environment in which you are using the system, you might encounter static-type noises during single channel operation caused by received radio interference on the open, unused channel which is also mixed into the audio output you are amplifying. If this happens turn on the second microphone transmitter, and if not using, leave nearby (~5—10 feet away) with the OFF/STANDBY/ON (10) switch in the STANDBY position, which means the transmitter is operating but the audio input is muted. The second channel’s LED (7) should now also be lit. This should eliminate the interference static.

[Note: Observe care in selecting amplified volume, transmitter location and speaker placement so that acoustic feedback (howling or screeching) will be avoided.]

SPECIFICATION

OVERALL SYSTEM PERFORMANCE	Battery Life: Up to 15 hours
Frequency Response: 80-12,000 Hz, +/-3dB	Dimensions (L x Dia): 9.5” x 1.3” x 2”, (24.2cm x 3.2cm x 5.1cm)
Dynamic Range: 80dB	Weight (w/o battery): 6.0 oz., (170g.)
Total Harmonic Distortion: <3%	RECEIVER
RF Carrier Frequency Range: 81-87 MHz
Frequency Stability: +/- 0.005%	Control: Power ON/OFF
Modulation: FM (F3E), +/-75KHz max.	Connector: 1/4” unbalanced audio out jack (both channels mixed
Operating Range: 100 ft. typical-up to 200+ ft. line-of-sight	together)
TRANSMITTER	LED Indicator: Power ON, Transmitter RF (one each, both channels)
	Antennas: 15.3”, (38.8cm), dual collapsible antennas
Audio Input: unidirectional dynamic cartridge	Power Requirement: AC/DC 9VDC/0.2A
Controls: OFF/STANDBY/ON switch	Dimensions (W x H x D): 11.8”x 1.8”x 4.5”,
LED Indicator Unit: “ON”	(29.9cm x 4.5cm x 11.5cm.)
RF Power Out: Up to 50mW (Max. allowed by FCC)	Weight: 11.3 oz., (320g.)
Harmonic & Spurious Emissions: <-40dB
Battery: 9V Alkaline	Specifications subject to change for product improvement purposes

SERVICE

(U.S.) Should your Nady American Starpower™ X2 Wireless Microphone System require service, please contact the Nady Customer Service Department via telephone: (510) 652-2411 or e-mail: service@nady.com.

(INTERNATIONAL) For service, please contact the Nady distributor in your country through the dealer from whom you purchased this product.

The warranty card supplied with this system provides valuable warranty and service information. Store it in a safe place for future reference. Do not attempt to service this unit yourself as it will void your warranty.

NADY SYSTEMS, INC.

6701 Shellmound Street • Emeryville, CA 94608 • Tel: 510.652.2411 • Fax: 510.652.5075 • www.nady.com