Napoleon Fireplaces GDIZC-N Insert Vent Connection, Chimney Connection, Screws. Then seal, Liner

6

INSERT VENT CONNECTION

Move the insert close to its final position inside the wood- burning fireplace. This unit is equipped with 6 levelling screws located as follows: two are on either side of the circulation blower on the rear panel; four are located front and back on either side beneath the log support. Level using four of the lev- elling screws. See Figure 1a. Levelling the unit will eliminate rocking or excessive noise when the fan is in operation. Once the unit is level, move it partially into place within the fireplace to allow for all connections to be made. It is not practical to level the insert once the it has been installed. Determine the required depth prior to installing the unit and adjust the four levelling screws accordingly.

CHIMNEY CONNECTION

2.Gently stretch the liners to the required lengths and in- sert into the chimney. Place the terminal onto the top of the chimney cap and fit the flashing plate to suit. Make weather tight by sealing with caulking (not supplied) and fasten to the chimney with screws and plugs (not supplied)

3.INSIDE: Attach and secure the flex liners to the vent connection assembly using the same procedure as before, ensuring that the marked exhaust liner is attached to the exhaust collar.

VENT

HI-TEMP CONNECTION SEALANT

ASSEMBLY

FIGURE 3 2" OVERLAP

Chimney installation must conform to both national and local code requirements. The chimney must be lined with one 2" or 3" diameter liner for intake and one 3" diameter liner for exhaust. The minimum and maximum vent lengths are 10 and 35 feet respectively. Recommended Napoleon kits come in 3 lengths: While the liners must be continuous from the fireplace to the terminal, to achieve the needed length, they may be coupled, using an aluminium coupler, provided installation is sealed & secured.

1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST

&

2-3" TO 2" REDUCER:

EXHAUST

FIGURE 4

INTAKE

GDI-2320KT	VENT KIT 20FT
GDI-2325KT	VENT KIT 25FT
GDI-2335KT	VENT KIT 35FT
2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:
GDI-320KT	VENT KIT 20FT
GDI-325KT	VENT KIT 25 FT
GDI-335KT	VENT KIT 35 FT

We recommend that exhaust vents that pass through un- heated spaces, such as a garage or attic, be wrapped in a protective sleeve to minimize condensation and reverse flow symptoms. See Trouble Shooting for details.

This unit is approved for use with a 2" liner for air intake and a 3" liner for exhaust. For best performance, however, it is recommended to use two 3" liners.

If a 2" liner is used for the intake, it is necessary to adjust the primary air shutter. See "Air Shutter Settings" on page 11.

1. OUTSIDE: Slip one	TERMINAL FIGURE 2
end of a liner a minimum of	GDI-223
2" over one of the collars of
	FLASHING
the terminal. Secure using
	PLATE
3 screws. Then seal the
	2"
joint and screw heads with
	OVERLAP
high temperature seal-
ant. Repeat with the other

liner.	EXHAUST	SEALANT
	COLLAR LABELED
	INTAKE	HI-TEMP

NOTE: We recommend that the other end of the exhaust liner be marked to eliminate the exhaust liner being connected to the intake collar at the unit.

4.Detach the two screws from the back of the firebox and remove the panel, as illustrated.

	STUDS
VENT
CONNECTOR	RESTRICTOR
EXTENSION
	PLATE
FIGURE5a-b

5.Reaching in through the insert, manoeuvre the vent con- nection assembly through the openings in the firebox top, taking care not to damage the gasket. In case of a low ceiling fireplace, the extension should be removed and reinstalled after the vent connection is secured to the firebox. Attach the restrictor plate to the centre stud and secure the assembly using the three studs and ¼-20 hex nuts.

W415-0223 / E / 03.05.09