Napoleon Fireplaces GDIZC-N manual Operation / Maintenance, Operating Instructions

9

OPERATION / MAINTENANCE

OPERATING INSTRUCTIONS

The on-off switch is located behind the left side control door.

Purge all gas lines with the glass door open. Assure that a continuous gas flow is at the burner before closing the door. Allow several minutes (5-15) for the flame to stabilize after ignition.

Do not operate the main burner of the insert with the door removed.

When lit for the first time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the "burn-in" of paints and lubricants used in the manufac- turing process and will not occur again. Simply open a window to sufficiently ventilate the room. After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may emit a slight odour for a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to sufficiently ventilate the room.

PURGE THE GAS LINE WITH THE GLASS DOOR OPEN.

FOR YOUR SAFETY READ BEFORE LIGHTING:

A. This fireplace is equipped with a pilot which must be lit by hand. While following these instructions exactly.

B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the floor.

C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control system and any gas control which has been under water.

WHAT TO DO IF YOU SMELL GAS:

•Turn off all gas to the fireplace.

•Open windows.

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire depart-

ment.

FIGURE 19

FLAME ADJUSTMENT ON/OFF KNOB

KNOB FIGURE 20

LIGHTING INSTRUCTIONS

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed slightly.

1.Stop! Read the above safety information on this label.

2.Turn off all electric power to the fireplace.

3.Turn the gas knob clockwise to off.

4.Wait five (5) minutes to clear out any gas. If you smell gas including near the floor. Stop! Follow "B" in the above safety in- formation on this label. If you don't smell gas go the next step.

5.If fireplace is equipped with flame adjustment valve turn clockwise to off.

6.Find pilot located in front of back log.

TO TURN OFF GAS

7.Turn gas knob counter-clockwise to pilot.

8.Depress slightly and hold gas knob while lighting the pilot with the push button ignitor. Keep knob depressed for one minute, then release. If pilot does not continue to burn, repeat steps 3 through 7.

9.With pilot lit, depress and turn gas knob counter-clockwise to on.

10.If equipped with flame adjustment valve, push and turn knob to high.

11.If equipped with remote on-off switch/thermostat, main burner may not come on when you turn valve to on. Remote switch must be in the on position to ignite burner.

12.Turn on all electric power to the fireplace.

1. Turn off all electrical power to the unit if service is to be	2. Push in gas control knob slightly and turn clockwise
performed.	to off. Do not force.
	2. Keep the control compartment, logs, burner, air shutter
MAINTENANCE
	opening and the area surrounding the logs clean by vacu-
TURN OFF THE GAS AND UNPLUG ELECTRICAL
	uming or brushing, at least once a year.
POWER BEFORE SERVICING THE FIREPLACE INSERT!	3. Check to see that all burner ports are burning. Clean out
CAUTION: Label all wires prior to disconnection when servic-	any of the ports which may not be burning or are not burn-
ing controls. Wiring errors can cause improper and dangerous	ing properly.
operation. Verify proper operation after servicing. This insert	4. Check to see that the pilot flame is large enough to engulf
and its venting system should be inspected before use and	the thermocouple on one leg and reaches toward the burner
at least annually by a qualified service person. The fireplace	on the other leg.
area must be kept clear and free of combustible materials,	5. Replace the cleaned logs.
gasoline or other flammable vapours and liquids. The flow of	6. Check to see that the main burner ignites completely on
combustion and ventilation air must not be obstructed.	all openings when the gas knob for the burner is turned on.
1. In order to properly clean the burner and pilot assembly,	A 5-10 second total light-up period is satisfactory. If ignition
remove the logs exposing both assemblies.	takes longer, consult your Napoleon dealer/distributor.
	7. Check that the door gasketing is not broken or missing.
	Replace if necessary.	W415-0223 / E / 03.05.09