National Instruments NI CVS-1450 Series Accessories

Chapter 2 Setup and Configuration

NI CVS-1450 Series User Manual 2-2 ni.com

❑10 m 10/100Base-T Ethernet cable (part number

189174-10)—Standard Category 5 (CAT-5) 10/100Base-T Ethernet

cable that connects the CVS-1450 device to a network port. To connect

the CVS-1450 device directly to a local development computer, use an

Ethernet crossover cable.

Note To maintain signal integrity, the Ethernet cable length must be no longer than 100 m.

Software

❑NI-IMAQ for IEEE 1394 Cameras driver software, which includes the

CVS-1450 Series support software

❑One of the following application software packages:

– NI Vision Builder for Automated Inspection (AI) 2.0 or later

– NI LabVIEW Real-Time Module 7.0 or later with the Vision

Development Module 7.0 or later

Accessories

National Instruments offers the following accessories for use with a

CVS-1450 device.

Hardware

• VGA-resolution camera (part number 778785-01)

• 12 mm fixed focal length lens (part number 778789-01)

• LED ring light (part number 778787-01)

• NI Vision I/O terminal block and prototyping accessory (part number

779166-01)

• DIN rail/panel mount kit (part number 189154-01)

• Digital I/O cable and horizontal DIN rail terminal block (part number

778790-01)

• Digital I/O cable and vertical DIN rail terminal block (part number

778791-01)

•75 Ω SMB 111 coaxial cable (part number 763422-01)—SMB to

BNCcable for connecting to triggers and light sources

• 10 m Ethernet crossover cable (part number 187375-10)—For

connecting the CVS-1450 device directly to the development

computer

Contents

Main Page Important Information Warranty Copyright Trademarks Patents Compliance Compliance with FCC/Canada Radio Frequency Interference Regulations Determining FCC Class FCC/DOC Warnings Class A Conventions Contents Chapter 1 NI CVS-1450 Series Overview Chapter 2 Setup and Configuration Chapter 3 LEDs, DIP Switches, and Connectors Chapter 4 Digital I/O Functionality Page NI CVS-1450 Series Overview About the NI CVS-1450 Series Hardware Overview Figure1-1 shows the CVS-1450 Series front panel. Figure 1-1. CVS-1450 Series Front Panel Available Camera Bandwidth Software Overview NI-IMAQ for IEEE 1394 Cameras Driver Software National Instruments Application Software Vision Builder for Automated Inspection LabVIEW Real-Time Module with the Vision Development Module Page Setup and Configuration Required Items Hardware Software Accessories Hardware Documentation Safety Information Page Setup Overview Before Getting Started: Connecting the CVS-1450 Device to a Network Subnet Considerations Setting Up the Hardware Connecting a Camera and Monitor to the CVS-1450 Device Wiring Power to the CVS-1450 Device Connecting to a Separate Main Supply Page Connecting the CVS-1450 Device to the Development Computer Vision Builder AI: Setting up the Development Computer Installing Vision Builder AI and NI-IMAQ for IEEE 1394 Cameras Configuring the IP Address on the CVS-1450 Device Acquiring an Image in Vision Builder AI LabVIEW Real-Time Module with the Vision Development Module: Setting up the Development Computer Configuring the IP Address using the LabVIEW Real-Time Module Downloading Software onto the CVS-1450 Device Acquiring an Image Using the LabVIEW Real-Time Module Page LEDs, DIP Switches, and Connectors LED Indicators POWER OK LED STATUS LED ACT/LINK LED 100 Mbps LED DIP Switches SAFE MODE Switch IP RESET Switch NO APP Switch USER 1 Switch (LabVIEW Real-Time Module Users) Connectors Power Connector Earth Ground Connection IEEE 1394 VGA Page COM1 Ethernet TRIG 0 TRIG 1 and TRIG 2 General-Purpose Digital I/O Page Page Page Page Digital I/O Functionality Overview TTL and Isolated Inputs and Outputs TTL Inputs and Outputs Isolated Inputs and Outputs Table4-2 summarizes the isolated inputs and outputs available on the CVS-1450 device. I/O for Normal Operation Trigger Inputs Timed Pulse Output Initiating a Timed Pulse Pulse Modes Pulse Delay Pulse Width Trigger Polarity Quadrature Encoder Product Selection Port Using ISO Input 5 as a Latch General-Purpose I/O General-Purpose Inputs General-Purpose Outputs I/O for Fault Conditions Shutdown Disabling Shutdown Mode Watchdog Timer Overheat Considerations When Connecting the Digital I/O Wiring an Isolated Input to a Sourcing Output Device Wiring an Isolated Output to an External Load Protecting Inductive Loads Transmission Line Effects Typical System Setup Page Deployment Connecting Multiple CVS-1450 Devices Page Page A Troubleshooting Software Configuration Problems CVS-1450 Device Does Not Appear in MAX or in Vision Builder AI Error When Configuring IP Settings for the CVS-1450 Device Status of CVS-1450 Device in MAX and Vision Builder AI is No Software Installed No Camera Found Formatting the CVS-1450 Device Compact Flash Memory Hardware Errors POWER OK LED is Red Cannot Drive Isolated Outputs Runaway Startup Application System Displays a Missing Operating System Error at Startup LED Error Indications POWER OK LED Is Not Lit When the CVS-1450 Device is Powered On B Specifications Power Requirements Memory Processor Network TTL Inputs and Outputs TTL Inputs TTL Outputs Optically Isolated Inputs and Outputs Isolated (Current Sinking) Inputs Isolated (Current Sourcing) Outputs IEEE 1394 Physical Characteristics Environmental Safety Electromagnetic Compatibility CE Compliance C Mounting Information Mounting the CVS-1450 Series Page Page Page D Technical Support and Professional Services Page Glossary B D E F Page Page Index Numerics A B C E F G H I K L M N O R S T V