Caution when placing the plasma monitor in portrait mode

 

 

Top side

•

Use the optional unit. Contact your store of purchase when installing.

 

 

 

 

 

 

 

OPTION1

 

 

 

 

 

OSM

 

 

 

 

•

Rotate 90° clockwise as seen from the front when installing.

 

 

 

 

 

 

 

 

RGB SELECT: RGB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BNC INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

:

RGB

 

 

 

 

 

 

 

90°

 

D - SUB INPUT

 

 

 

 

•

After installing, make sure the NEC logo is located at the

 

 

:

AUTO

 

 

 

 

 

 

 

 

 

 

 

 

 

ALL RESET:

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HD SELECT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

:

1080B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT SKIP

 

 

 

 

 

 

left hand side of the screen when facing the plasma from

 

 

 

 

 

 

 

 

 

:

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1024￿768

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEL. MENU/ENTER OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT RETURN

 

 

 

 

 

the front.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Be sure to set “OSM ANGLE” to “V” when using.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* Failure to heed the above cautions may lead to malfunction.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Using the remote control

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Battery Installation and Replacement

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Insert the 2 “AAA” batteries, making sure to set them in

 

 

 

 

 

 

 

 

 

Bottom side

with the proper polarity.Operating Range

 

 

 

 

 

 

 

1. Press and open the cover.

 

 

 

 

 

 

 

 

 

* Use the remote control within a distance of about 7 m/

 

 

 

23ft. from the front of the monitor’s remote control sensor

 

 

 

and at horizontal and vertical angles of up to approximately

 

 

 

30°.

 

 

 

 

 

 

 

 

 

 

 

 

 

* The remote control operation may not function if the

 

 

 

monitor’s remote control sensor is exposed to direct

2. Align the batteries according to the (+) and (–) indication

 

sunlight or strong artificial light, or if there is an obstacle

 

between the sensor and the remote control.

 

inside the case.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Approx.7m/23ft3.Replace the cover.
Using the wired remote control mode

Connect the remote cable* to the remote control’s remote jack and the “REMOTE IN” terminal on the monitor. When the cable is connected, the mode automatically switches to wired remote control. When the wired remote control mode is used, the remote control can be operated even if no batteries are loaded.

OUTN I

REMOTE Control External

Remote Control

Cable*

To Remote Jack

Handling the remote control•Do not drop or mishandle the remote control.

•Do not get the remote control wet. If the remote control gets wet, wipe it dry immediately.

•Avoid heat and humidity.

•When not using the remote control for a long period, remove the batteries.

•Do not use new and old batteries together, or use different types together.

•Do not take apart the batteries, heat them, or throw them into a fire.

•When using the remote control in the wireless condition, be sure to unplug the remote cable from the REMOTE IN terminal on the monitor.

* The 1/8 Stereo Mini cable must be purchased separately. En-6