NEC LCD2690WUXi user manual Hdcp Content, English-21

Tag6	Color Control	Colour Control Systems: Seven preset colour settings.
		For preset settings 1, 2, 3 and 5, the following levels can be adjusted:
		TEMPERATURE: Adjust the white temperature by increasing or decreasing this setting.
		A lower colour temperature will make the screen reddish and a higher colour temperature
		will make the screen bluish.
		WHITE (White Balance): If TEMPERATURE needs further adjustment; the individual
		R/ G/ B/ levels of the white point can be adjusted. To adjust the R/G/B levels, CUSTOM
		must be showing as the TEMPERATURE selection.
		HUE: Adjusts the hue of each colour*1. The change in colour will appear on screen and
		the menu colour bars will show the amount of adjustment.
		SATURATION: Adjusts the colour depth of each colour*1. Press the ÒRIGHTÓ button and
		the colour vividness increases.
		OFFSET: Adjusts the colour brightness of each colour*1. Press ÒRIGHTÓ button and the
		colour Brightness increases.
		*1: RED, YELLOW, GREEN, CYAN, BLUE and MAGENTA.
		NATIVE, sRGB: Original colour presented by the LCD panel that is unadjustable.
		PROGRAMMABLE: The colour tone that was set up with the downloaded application
		software is reflected.
Tag7	Sharpness	This is a digital capability for keeping a crisp image at all signal timings. It continuously
		adjusts to maintain a distinct or soft image as you prefer, and is set independently
		according to different timings. Press ÒLeftÓ or ÒRightÓ to adjust.
	DVI Selection	This function selects the DVI input mode. When the DVI selection has been changed, you
		must restart your computer. Press ÒLeftÓ or ÒRightÓ to select.
		AUTO: By using the DVI-D to DVI-D cable, the DVI SECTION is DIGITAL.
		By using the D-SUB to DVI-A cable, the DVI SECTION is ANALOG.
		DIGITAL: DVI digital input is available.
		ANALOG: DVI analog input is available.
	HDCP CONTENT	Selects the type of input to be used with HDCP CONTENT.
	(Digital Input Only)	OFF: When a PC or other computer equipment is connected, select ÒOFFÓ.
		ON: When a DVD player or other type of high definition device is connected, select ÒONÓ.
		Note: Interlaced signals (480i, 576i, 1080i) are not supported. If you have any problems,
		please refer to the Troubleshooting section of this UserÕs Manual.
	Video Detect	Selects the method of video detection when more than one computer is connected.
		Press ÒLeftÓ or ÒRightÓ to select.
		FIRST: The video input has to be switched to ÒFIRSTÓ mode. When current video input
		signal is not present, then the monitor searches for a video signal from the other video
		input port. If the video signal is present in the other port, then the monitor switches the
		video source input port to the new found video source automatically. The monitor will not
		look for other video signals while the current video source is present.
		LAST: The video input has to be switched to the ÒLASTÓ mode. When the monitor is
		displaying a signal from the current source and a new secondary source is supplied to the
		monitor, then the monitor will automatically switch to the new video source. When current
		video input signal is not present, then the monitor searches for a video signal from the
		other video input port. If the video signal is present in the other port, then the monitor
		switches the video source input port to the new found video source automatically.
		NONE: The Monitor will not search the other video input port unless the monitor is
		turned on.
	Off Timer	Monitor will automatically turn off after the preset time period from power on with the
		ON/OFF function. When you select ÒONÓ, press ÒSELECTÓ and ÒLeftÓ or ÒRightÓ to adjust.
		Before powering off, a message will appear on the screen asking the user if they want to
		delay the turn off time by 60 minutes. Press any OSM button to delay the turn off time.
	IPM (Intelligent Power	The Intelligent Power Manager allows the monitor to enter into a power saving mode after
	Manager)	a period of inactivity. The IPM has three settings.
		OFF: Monitor does not go into power save mode when the input signal is lost.
		STANDARD: Monitor enters power save mode automatically when the input signal is lost.
		OPTION: Monitor enters power save mode automatically when the amount of surrounding
		light goes below the level that is determined by the user.
	IPM Setting	Adjusts the ILLUMINANCE value for IPM.

English

English-21