WN604 IG 26July11.fm Page 2 Tuesday, July 26, 2011 6:00 PM

Deploy the WN604

Now that you have finished the setup steps, you are ready to deploy the access point in your network. If necessary, you can now reconfigure the PC you used in step 1 back to its original TCP/IP settings.

1.Disconnect the access point from the computer and place it where you will deploy it. The best location is elevated, such as a wall, ceiling, or the top of a cubicle. The access point should be placed near the center of your wireless coverage area and within line of sight of all the mobile devices.

2.Connect an Ethernet cable from your access point to a LAN port on your router, switch, or hub.

3.Connect the power adapter to the access point and plug the power adapter into an AC power outlet. The Power, WLAN, and LAN LEDs should light up.

Verify Wireless Connectivity

Before installing in a remote location, use a computer with an 802.11g, 802.11b, or 802.11n wireless adapter and verify connectivity. Use a browser such as Netscape®, Internet Explorer, or Mozilla Firefox® to connect to the Internet, and check for file and printer access on your network.

Note: If you cannot connect, see the Troubleshooting Tips in this guide or the link to the reference manual on the Resource CD.

Troubleshooting Tips

Here are some tips for correcting simple problems you might have.

No LEDs are lit on the access point.

The access point has no power.

Make sure that the power supply is connected to the access point and plugged in to a working power outlet or power strip.

Make sure that you are using the NETGEAR power supply provided with your access point.

July 2011

The LAN LED is not lit.

There is a hardware connection problem.

Make sure that the cable connectors are securely plugged in at the access point and the network device (hub, switch, or router).

Make sure that the connected device is turned on.

The WLAN LED is not lit.

The access point’s antennas are not working.

If the WLAN activity LED stays off, disconnect the adapter from its power source and then plug it in again.

Contact NETGEAR if the WLAN LED remains off.

I cannot configure the access point from a browser.

Check these items:

The access point is properly installed and it is powered on. Check that the LAN port LED is green to verify that the LAN connection is OK.

If your PC uses a fixed (static) IP address, ensure that it is using an IP address in the range of the WN604. The WN604 default IP address is 192.168.0.100 and the default subnet mask is 255.255.255.0. The access point default setting is for a static IP address. If the network where you are connecting it is using DHCP, configure it accordingly. See the reference manual on the Resource CD for more details.

Note: The factory default reset button and the default settings for your access point are located on the label at the rear of your access point.

I cannot access the Internet or the LAN with a wireless capable computer.

Confirm that the network is connected to the Internet. The problem could be with the router and not with the access point.

There is a configuration problem. Check these items:

You might not have restarted the computer with the access point to have TCP/IP changes take effect. Restart the computer.

The computer with the wireless adapter might not have the correct TCP/IP settings to communicate with the network. Restart the computer and check that TCP/IP is set up correctly for that network. The usual setting for Windows in the Network Properties is “Obtain an IP address automatically.”

The access point’s default values might not work with your network. Check the access point default configuration against the configuration of other devices in your network.

For full instructions on changing the access point’s default values, click the documentation links on the Resource CD or on the menu of the WN604 access point user interface.

Technical Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and use it to register your product at http://www.NETGEAR.com/register. Registration is required before you can use the telephone support service. Registration through the NETGEAR website is strongly recommended.

Go to http://support.netgear.com for product updates, documentation, and support.

For additional information about setting up, configuring, and using your ProSafe Wireless N150 Access Point WN604, see the reference manual.

For complete DoC please visit the NETGEAR EU Declarations of Conformity

website at: http://support.netgear.com/app/answers/detail/a_id/11621/

For GNU General Public License (GPL) related information, please visit

http://support.netgear.com/app/answers/detail/a_id/2649

WARNING!!

DO NOT stack equipment, or place equipment in tight spaces, or in drawers. Be sure your equipment is surrounded by at least 2 inches of air space.

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive.

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. Other brand and product names are registered trademarks or trademarks of their respective holders. © 2011 NETGEAR, Inc. All rights reserved.

Page 2
Image 2
NETGEAR WN604-100NAS manual Deploy the WN604, Verify Wireless Connectivity, Troubleshooting Tips, Technical Support