Abbildung / Figure 1
Abbildung / Figure 2

KMR 81 i

Die Zuordnung der Mikrophonanschlüsse und die Polarität der Modulationsadern ist am Ausgang der Speisegeräte die gleiche wie am Mikrophon.

The assignment of the microphone terminals and the modulation polarity at the power supply output are identical to those at the microphone.

3. Technische Daten

3. Technical Specifications

2.4Betrieb an unsymmetrischen oder mittengeerdeten Eingängen

Die 48 V-Phantom-Speisegeräte BS 48 i, BS 48 i-2 und N 248 haben gleichspannungsfreie Ausgänge, so dass für den Anschluss an unsymmetrische Ein- gänge kein Übertrager erforderlich ist.

Beim KMR 81 i ist Pin 2 normgemäß die „heiße Phase“. Für unsymmetrische Eingänge muss PIN 3 am Ausgang des Speisegerätes an Masse gelegt werden (siehe Abbildung 1).

Bei vielen anderen als den o.g. Phantomspeisege- räten liegen nicht nur die Modulationsleitungen zum Mikrophon auf dem Potential der Speisespan- nung von +48 V, sondern auch die vom Speisege- rät abgehenden Modulationsleitungen. Für die in der Studiotechnik allgemein üblichen symmetri- schen und erdfreien Ver-

stärker und Mischpultein- gänge ist dies ohne Be- deutung. Dagegen wird

die Speisespannung beim Anschluss an einseitig

oder mittengeerdete Ver- stärkereingänge kurzge- schlossen, und es ist kein

Betrieb möglich. Dann be- stehen folgende Lö- sungsmöglichkeiten:

a)In mittengeerdeten Geräten mit Eingangs- übertrager (z.B. einige

NAGRA-Geräte) kann die betreffende Erdverbin- dung fast immer ohne Nachteile für die Funkti- on des Gerätes aufge- trennt werden.

b)In jede abgehende Modulationsleitung kann zur Abblockung der 48 V-

Gleichspannung eine RC- Kombination eingefügt werden (siehe Abbildung

2und Neumann-Informa- tion Nr. 84 221).

2.4Operation with Unbalanced or Center Tap Grounded lnputs

The BS 48 i, BS 48 i-2 and N 248 phantom 48 Vdc power supplies are dc-free so that no transformer is required for connection to unbalanced inputs.

In the case of the KMR 81 i condenser microphone pin 2 is the “hot phase“, in accordance with the standard, and pin 3 of the output of the power sup- ply must be connected to earth (see Fig. 1).

In the case of many other phantom powering units (except those mentioned above), not only the mod- ulation leads to the microphone, but also the out- going modulation leads from the powering unit, are at the potential of the feed voltage (+48 V). This is of no significance for the balanced, float-

ing amplifier and mixing console inputs in general studio use. On the other hand, the feed voltage will be short-circuited when connected to single -ended or center tap grounded amplifier in- puts, and no operation will be possible. This can be circumvented as fol- lows:

a) In center tap grounded equipment with input transformer (e.g. some NAGRA units), the earth lead can almost always be disconnected without affecting the function of the equipment.

b) In every outgoing modulation lead, an RC net-work can be incorporated to block the 48 Vdc voltage (See Figure 2 and Neumann-Information no. 84 222).

Akustische Arbeitsweise ...........

Druckgradienten-

 

interferenzempfänger

Richtcharakteristik ...................

Superniere/Keule

Übertragungsbereich ....................

20 Hz

...20 kHz

Feldübertragungs-

 

 

faktor1) ...................................

18 mV/Pa ± 1 dB

Nennimpedanz .....................................

150 Ohm

Nennlastimpedanz ..............................

1000 Ohm

Geräuschpegelabstand

 

 

CCIR 468-3 ..............................................

71 dB

Geräuschpegelabstand

 

 

DIN/IEC 651 .............................................

82 dB

Ersatzgeräuschpegel

 

 

CCIR 468-3 ..............................................

23 dB

Ersatzgeräuschpegel

 

 

DIN/IEC 651 ..........................................

12 dB-A

Grenzschalldruckpegel für

 

 

0,5 % Klirrfaktor2) ..................................

128 dB

0,5 % Klirrfaktor mit Vordämpfung2) .........

138 dB

Max. Ausgangsspannung .........................

1,3 dBu

Speisespannung3) ..............................

48 V ± 4 V

Stromaufnahme3) .....................................

0,8 mA

Erforderlicher Steckverbinder

..................

XLR 3 F

Gewicht ....................................................

145 g

Durchmesser ............................................

21 mm

Länge ...................................................

226 mm

1 Pa = 10 µbar

0 dB 20 µPa

1)bei 1 kHz an 1 kOhm Nennlastimpedanz. 1 Pa 94 dB SPL.

2)Klirrfaktor des Mikrophonverstärkers bei einer Eingangsspan- nung, die der von der Kapsel beim entsprechenden Schalldruck abgegebenen Spannung entspricht.

3)Phantomspeisung (P48, IEC 1938).

Acoustical op. principle

............. Pressure gradient

 

 

interference transducer

Directional pattern .....

Supercardioid/Lobe shaped

 

 

(Shotgun)

Frequency range ..........................

20 Hz...

20 kHz

Sensitivity 1) ............................

18 mV/Pa

± 1 dB

Rated impedance .................................

150 ohms

Rated load impedance .......................

1000 ohms

S/N ratio

 

 

 

CCIR 468-3 ..............................................

 

71 dB

S/N ratio

 

 

 

DIN/IEC 651 .............................................

 

82 dB

Equivalent SPL

 

 

 

CCIR 468-3 ..............................................

 

23 dB

Equivalent SPL

 

 

 

DIN/IEC 651 ..........................................

12 dB-A

Maximum SPL

 

 

 

for 0.5 % THD2) ......................................

128 dB

for 0.5 % THD with preattenuation2) .........

138 dB

Max. output voltage ................................

1.3 dBu

Supply voltage3) ................................

48 V ± 4 V

Current consumption3) ..............................

 

0.8 mA

Matching Connector .................................

XLR 3 F

Weight ......................................................

 

145 g

Diameter .................................................

 

21 mm

Length ..................................................

226 mm

1 Pa = 10 µbar

0 dB 20 µPa

1)at 1 kHz into 1 kohm rated load impedance.

1 Pa 94 dB SPL.

2)THD of microphone amplifier at an input voltage equivalent to the capsule output at the specified SPL.

3)Phantom powering (P48, IEC 1938).

6

7