Abbildung / Figure 1
Abbildung / Figure 2
8

Das Gerät BS 48 i-2 ist mit 5-poligen, das BS 48 i mit 3-poligen XLR-Steckverbindern ausgerüstet.

Ein Mikrophon der Serie fet 100 kann mit einem BS 48 i ca. 20 Stunden betrieben werden (siehe auch Neumann-Druckschrift 68832... „48 V-Phantomspeise- geräte“).

Die Zuordnung der Mikrophonanschlüsse und die Po- larität der Modulationsadern ist am Ausgang der Spei- segeräte die gleiche wie am Mikrophon.

3.4Betrieb an unsymmetrischen oder mittengeerdeten Eingängen

Die 48 V-Phantomspeisegeräte

BS 48 i, BS 48 i-2,

N 48 R-2 und N 48 i-2 haben

gleichspannungsfreie

Ausgänge, so daß für den Anschluß an einen unsym- metrischen Eingang kein Übertrager erforderlich ist.

Beim TLM 127 ist Pin 2 die „heiße Phase“, und Pin 3 muß für unsymmetrische Eingänge an Masse gelegt werden (siehe Abbildung 1).

Bei vielen anderen als den o.g. Phantomspeisegerä- ten liegen nicht nur die Modulationsleitungen zum Mi- krophon auf dem Potential der Speisespannung von +48 V, sondern auch die vom

Speisegerät abgehenden Mo- dulationsleitungen. Für die in der Studiotechnik allgemein

üblichen symmetrischen und erdfreien Verstärker- und Mischpulteingänge ist dies

ohne Bedeutung. Dagegen wird die Speisespannung beim Anschluß an einseitig oder mittengeerdete Verstärkerein- gänge kurzgeschlossen, und es ist kein Betrieb möglich.

Dann bestehen folgende Lö- sungsmöglichkeiten:

a)In mittengeerdeten Gerä-

ten mit Eingangsübertrager (z.B. einige NAGRA-Geräte) kann die betreffende Erdverbindung fast immer ohne Nachteile für die Funktion des Gerätes auf- getrennt werden.

b)In jede abgehende Modu- lationsleitung kann zur Abblok-

kung der 48 V-Gleichspannung eine RC-Kombination eingefügt werden (siehe Abb. 2 und Neu- mann-Information Nr. 84 221).

The BS 48 i-2 is equipped with 5-pin XLR connec- tors, the BS 48 i with 3-pin XLR connectors.

A fet 100 series microphone can be operated for ap- prox. 20 hours on a BS 48 i. See Neumann bulletin 68832... “Phantom 48 VDC Power Supplies”.

The assignment of the microphone terminals and the modulation polarity at the power supply output are identical to those at the microphone.

3.4Operation with Unbalanced or Center Tap Grounded Inputs

The 48 V phantom powering units BS 48 i, BS 48 i-2,

N48 R-2 and N 48 i-2 have DC-free outputs, so that no transformer is required for connecting to an unbal- anced input.

In the case of the TLM 127 condenser microphone pin 2 is the “hot phase”, and pin 3 must be connected to earth for ungrounded inputs (see Fig. 1).

In the case of many phantom powering units, other than those mentioned above, both the modulation leads to the microphone and the outgoing modulation leads from the powering unit are at the potential of the feed voltage (+48 V).

This is unimportant for the balanced, floating amplifier and mixing console inputs which are in general studio use. However, the feed voltage will be short-circuited if connected to single-sided or center tap grounded amplifier inputs, and no operation

will be possible.

This can be circumvented as follows:

a) For center tap grounded equipment with an input transformer (e.g. some NA- GRA units), the earth lead can almost always be disconnected without affecting the functioning of the equipment.

b)An RC network can be incorporated into every out-

going modulation lead, in order to block the 48 VDC voltage (See Fig. 2 and Neu- mann information sheet no. 84 221).

4. Technische Daten TLM 127

Akustische Arbeitsweise .......................

Druckgradienten-

 

empfänger

Richtcharakteristik ..................................................

Kugel, Niere,

(mit Fernsteuerung zusätzlich

Breite Niere, Hyperniere, Acht)

Übertragungsbereich .......................................

20 Hz

...

20 kHz

Feldübertragungsfaktor1) ...............................

12 mV/Pa ± 1 dB

Nennimpedanz ...............................................................

50 Ohm

Nennlastimpedanz ..................................................

1000 Ohm

Geräuschpegelabstand

 

 

 

CCIR 468-3 ..............................................................................

 

74 dB

Ersatzgeräuschpegel

 

 

 

CCIR 468-3 ..............................................................................

 

20 dB

Ersatzgeräuschpegel

 

 

 

DIN/IEC 651 .......................................................................

 

8 dB-A

Grenzschalldruckpegel für

 

 

 

0,5 % Klirrfaktor2) ..............................................................

 

140 dB

mit Vordämpfung ........................................................

 

154 dB

Max. Ausgangsspannung dabei ................................

 

10 dBu

Phantomspeisespannung

 

 

 

(P48, IEC 1938) .......................................................

48 V ± 4 V

Stromaufnahme pro Kanal ........................................

3,2 mA

Gewicht ..............................................................................

ca. 450 g

Abmessungen ............................................

58 mm x 173 mm

 

1 Pa = 10 µbar

 

0 dB

 

20 µPa

 

 

 

 

1)bei 1 kHz an 1 kOhm Nennlastimpedanz.

1 Pa 94 dB SPL.

2)Klirrfaktor des Mikrophonverstärkers bei einer Eingangsspannung, die der von der Kapsel beim entsprechenden Schalldruck abgege- benen Spannung entspricht.

4. Technical Specifications TLM 127

Acoustical op. principle ...........................

Pressure gradient

 

transducer

Directional pattern ..................

Omnidirectional, cardioid,

 

(wide angle cardioid, hyper-

 

cardioid and figure-8 also

available, via remote control)

Frequency range ................................................

20 Hz

...

20 kHz

Sensitivity1) ...................................................

12 mV/Pa ± 1 dB

Rated impedance .........................................................

50 ohms

Rated load impedance ..........................................

1000 ohms

S/N ratio

 

 

 

 

CCIR 468-3 ..............................................................................

 

 

74 dB

Equivalent SPL

 

 

 

 

CCIR 468-3 ..............................................................................

 

 

20 dB

Equivalent SPL

 

 

 

 

DIN/IEC 651) ......................................................................

 

 

8 dB-A

Max. SPL

 

 

 

 

for less than 0.5 % THD2)

.......................................................

 

140 dB

with preattenuation ...................................................

 

 

154 dB

Max. output voltage ........................................................

 

 

10 dBu

Phantom powering

 

 

 

 

(P48, IEC 1938) ......................................................

48 V ± 4 V

Current consumption per channel ........................

3.2 mA

Weight ......................................................................

approx. 450 g

Dimensions .................................................

58 mm x 173 mm

 

1 Pa = 10 µbar

 

0 dB

 

 

20 µPa

 

 

 

1)at 1 kHz into 1 kohm rated load impedance.

1 Pa 94 dB SPL.

2)THD of microphone amplifier at an input voltage equivalent to the capsule output at the specified SPL.

9