NewAir ACP-1300H Operating Instructions, Troubleshooting, Electric Diagram, Please Note

3. Operating Instructions

Air Exhaust Hose

The hot air exhaust conducts the hot, moist air produced by the unit away from the space you are cooling. The window kit and exhaust hose can also be moved from room to room with the unit. You can exhaust the ACP-1300H by following one of the following two methods:

1.Exhaust the hot air through a window or sliding glass door (a window kit extension may be necessary). Open the window or sliding glass door, install the window kit, and connect the exhaust hose.

50cm 50cm

2.If an existing window or sliding glass door cannot be used, a custom opening through a wall or ceiling can be cut out in order to facilitate the exhaust hose.

	50cm
Please Note:	50cm

The hot air must be exhausted in order for the unit to produce a cooling effect. When the ACP-1300H is not in use, safely store away the exhaust hose in a clean, dry place.

12

3. Operating Instructions

Exhaust Hose

1.The exhaust hose can extend from 1.8 feet to 6.5 feet. The shorter the hose , the better the cooling effect .

2.The hose should be as straight as possible, as sharp or unnece

-ssary bends in the hose will prevent effective airflow. This will subsequently result in overheating and possible shut-down of the unit.

3.The length of the exhaust hose should not be extended past 6.5 feet. Replacement hoses are available for purchase through your NewAir vendor. We also recommend that you use only certified NewAir re- placement parts.

13

4. Troubleshooting

Troubleshooting Your ACP-1300H Portable Air Conditioner

Before investing in repairs, check to see if any of the following apply to you:

Problems	Possible Causes	Suggested Solutions
	There could be power trouble.
	1.The power cord is not	1.Connect the power cord corre-
	plugged in.	ctly.
	2.The circuit breaker has
		2.Reset the circuit at the breaker
	been tripped.
		box.
The unit doesn't work.	3.There is a problem with
		3.Change the socket or outlet.
	the socket or outlet.
		4.Take the unit to a qualified techn-
	4.Either the power cord is
		ician and have the fuse replaced
	damaged, or the fuse
	needs to be replaced.	(fuse specification: 3A/250V).
	Either the timer has been
The unit stops working on its own.	activated or the temperature	Either turn the timer off or wait
	in the room is lower than the	for the room temperature to rise.
	set temperature.
	1.The room temperature is	1.Wait for the room temperature
		to rise to resume normal
There is no cool air coming out	lower than the set temp-
		operation.
of the unit when it is in cooling	erature.
		2.Allow the evaporator to defrost
mode.	2.The evaporator is frosted
		and normal operation will
	over.
		resume.
There is no cool air coming out of	1.The evaporator is frosted	Allow the evaporator to defrost
	over.
		andnormal operation will resume.
the unit when it is in dehumidifying
	2.The unit is eliminating frost.
mode.
Error code E2 is displayed on the	The water tank is full.	Empty the water tank and restart
control pane.l		the unit.
Error code E4 is displayed on the	The coil pipe is damaged.	Replace the coil pipe.
control panel.
	1.The voltage is too high or	1.Restart the unit when the voltage
Error code E1 is displayed on the		is normal.
	too low.
control panel.		2.Have the unit repaired by your
	2.The unit is damaged.
		NewAir dealer or at a professional
		repair center.

Please Note:

Never service your ACP-1300H portable air conditioner by yourself. If your unit needs to be repaired, please contact your NewAir dealer or a professional repair center for assistance.

14

5. Electric Diagram

15