Tech Tips: Optimizing Sonic Performance

Bass response is smoothest when the speaker is mounted within a rigid wall that flexes very little. For improved perfor- mance, add 2”x4” cross-braces horizontally roughly one foot above and one foot below the speaker location. Use wood glue and extra screws when attaching the drywall to the studs around the speaker. Additionally, once the speaker cutout has been made in the drywall, add a bead of wood glue inside the wall where the drywall meets the studs and cross- braces. If possible, use two layers of drywall for maximum rigidity.

For more controlled bass response, add insulation to the wall cavity around and behind the speaker to provide acoustic damping. Be sure to add the same amount of insulation to speakers in the same room to ensure consistent sound. Use R-12 or R-19 fiberglass insulation, and be sure to wear protective gloves to avoid contact with the fibers. If the insulation is paper- or foil-faced, position the paper or foil side away from the speaker.

now before installing the baffle (see “Painting”).

8.Connect the speaker cable to the spring posts on the SuperOne Ci baffle, making sure to observe correct polarity (see “Connections”).

9.Place one of the large foam isolators in each of the six raised bosses on the bezel. Place one of the small foam iso- lators in each of the 6 holes on the front surface of the baffle. Put the baffle into the bezel so the holes on the baffle line up with the holes in the center of the raised bosses on the bezel (fig. 10). Push one of the 4 x 16mm screws through a hole on the baffle and into the hole on the bezel and tighten it by hand so that the baffle and the bezel stay together. Insert the remaining screws, then tighten all of them snugly, making sure not to overtighten, as this may compromise the fit of the baffle. The use of power screwdrivers is not recommended. Exersize caution not to damage the drivers when inserting the screws.

10. Attach the metal grille by inserting it into the grooves in the baffle.

„Painting

 

 

 

The bezel frame and grille of the SuperOne Ci are finished in a matte white powder-coated

 

fig.11

 

 

 

 

finish that may be painted to match the wall. The frame and grille may be painted either

 

 

 

 

before or after the speaker is installed. Keep in mind that the grille contains hundreds of

 

 

 

 

tiny holes that are essential to the sound of the speaker. Take care not to cover these holes

 

 

 

 

 

 

 

 

with paint.

 

 

 

 

 

 

 

 

1. Paint the bezel frame and the grille at the same time using the same paint. Use the

paint shield (fig.11) to protect the inside of the bezel from overspray (paint will reduce the effective- ness of the absorptive materials). Fold the corners down and insert the paint shield into the grooves where the grille would attach. Be careful not to punch through the round hole in the middle of the shield.

2.When using spray paint, apply two thin coats, making sure to let the first coat dry completely before applying the second. This will avoid running. When using a compressor and spray gun, apply the

paint using its finest setting. Painting with a brush is not recommended, but when necessary be sure to thin the paint so as not to cover the holes in the grille. If paint does cover any of the grille holes, poke them out with a paper clip.

3.Once painting is complete, remove the paint shield from the bezel by carefully punching out the round hole in the middle, and using this hole to pull the shield free. Do not attempt to paint the black baffle surface (which houses the drivers) behind the grille. Its black finish prevents the speaker’s black drive units from being visible once the grille is attached.

„ Connections

Before connecting speakers to your system, it is important that you turn off the power to your amplifier / receiv- er to avoid damage to the equipment. Before installing the SuperOne Ci, map out the wiring paths between the speakers and the amplifier. Make sure that the speaker cable does not rest on sharp or pointed objects.

The SuperOne Ci is compatible with virtually all quality amplifiers. Proper wiring of the speakers is essential to good sound. At a minimum, 16AWG 2-conductor speaker cable is recommended for runs of 10 feet or less, with heavier special purpose speaker cable used for longer runs. For best results, use equal length runs of cable for the left and right

Page 5 Page 7
Page 6
Image 6
NHT SuperOne Ci owner manual Tech Tips Optimizing Sonic Performance, „ Painting, „ Connections
Page 5 Page 7

SuperOne Ci specifications

The NHT SuperOne Ci is an innovative and versatile loudspeaker designed to cater to the audio demands of home theater enthusiasts and audiophiles alike. Combining elegance with advanced technology, the SuperOne Ci is designed to deliver an unparalleled listening experience while seamlessly integrating into various environments, from contemporary living spaces to traditional setups.

One of the standout features of the NHT SuperOne Ci is its compact design. The speaker is engineered for a smaller footprint, making it ideal for users with limited space. Despite its size, it doesn’t compromise on sound quality. The SuperOne Ci is equipped with a 5.25-inch woofer, providing deep, resonant bass response. Accompanying this is a 1-inch soft dome tweeter that ensures clear and articulate high frequencies, allowing music and dialogue to shine through with remarkable clarity.

The SuperOne Ci utilizes a unique acoustic suspension design, which optimizes the speaker’s performance, delivering tight bass and a balanced tonal range. This feature is particularly beneficial in smaller rooms where excessive bass can lead to muddiness. The speaker also has a frequency response range that extends from 70 Hz to 30 kHz, ensuring it reproduces a wide array of sonic details, from subtle nuances to impactful soundscapes.

Moreover, the NHT SuperOne Ci is engineered with advanced materials for durability and performance. The cabinet is constructed from high-quality MDF to reduce resonance and unwanted vibrations, resulting in a clearer sound profile. The speaker’s finish options, including sleek black and sophisticated white, allow it to complement any décor seamlessly.

In terms of connectivity, the SuperOne Ci is designed for versatility. It can be easily integrated into existing home theater systems, making it perfect for both stereo and multi-channel setups. With its 8-ohm impedance, the speaker is compatible with a wide range of amplifiers, ensuring that users have flexibility no matter their audio source.

Lastly, NHT’s commitment to quality control and sound engineering is evident in the SuperOne Ci. Each unit undergoes rigorous testing to guarantee consistent performance and reliability. This attention to detail makes the NHT SuperOne Ci not only a great entry point for listeners new to high-fidelity audio but also an exceptional choice for seasoned audiophiles seeking a compact speaker solution.
Top Page Image Contents