Final Installation in New or Existing Construction

Final Installation in New or Existing Construction

1.If it is possible to lay a batt of insulation into the ceiling cavity do so. Remember to use equal amounts of insulation for each speaker.

2.Check the position of the Impedance Jumper on the crossover PC board. Choose the 4 ohm position if you are using an amplifier capable of drawing a 4 ohm load and you have only one pair of speakers connected. Otherwise, use the 8 ohm position (See Figure 15).

3.Separate the speaker wire so that at least two inches of each conductor are free.

4.Open the no-strip terminal by applying pressure to the red and black levers until an audible “click” is heard.

5.Insert one unstripped wire fully into the black and one into the red terminal. Pay attention to the markings on the wire. Each speaker must be connected to the amplifier in the same way. If unsure, see “Speaker Phase” located on the fol- lowing page. Squeeze the red and black levers until they click signifying that they have locked into the wire. Check to make sure that the knife assembly inside the no strip connector has prop- erly pierced the wire (See Figure 16).

6.Insert the no strip terminal into the corresponding socket on the rear of the speaker. Push it down until it locks in place. The terminal will only fit in the socket in one direction. If the ter- minal does not properly seat, reverse the terminal

7.On both models, there are four clamps or mounting “dogs” which hold each speaker in place. The dogs are tight- ened via four front-baffle screws. To install the speaker, first rotate the dogs inward. Insert the speaker into the cutout and tighten the dogs by turning the screws clockwise. DO NOT OVER- TIGHTEN THESE SCREWS. Over-tight- ening the clamps may make the grille difficult to install. (See Figure 17).

NOTE: The screws will be easier to turn if you “prime” them first. Before installing each speaker, turn the screws in and then turn them back out to their original positions.

8.Direct the Tweeter. The tweeter is directed by gently pushing on the edge of the tweeter grille. It will move 20° in any direction. For critical listening point the tweeter to the user’s favorite listen- ing position minimizing reflections from the side walls. For surround sound or low volume background listening cre- ate more reflections and thus more ambience by directing the tweeter towards the side walls. See Speaker Placement on Page 6.

Figure 15 Setting the Impedance Jumper.

Figure 16 No-Strip Speaker Wire Terminal.

15

Page 15 Page 17
Page 16
Image 16
Niles Audio CM5HD, CM6HD, CM8HD manual Final Installation in New or Existing Construction
Page 15 Page 17

CM6HD, CM8HD, CM5HD specifications

Niles Audio has long been synonymous with high-quality sound solutions, and their line of in-ceiling speakers, the CM5HD, CM8HD, and CM6HD, showcases this commitment to excellence. Designed for residential and commercial applications, these speakers combine aesthetics with performance, making them ideal for any setting.

The CM5HD is the entry-level model, yet it doesn't compromise on sound quality. With its 5.25-inch polypropylene woofer and 1-inch silk dome tweeter, it delivers clear, balanced audio across various frequency ranges. The CM5HD is equipped with a patented Tri-Logic™ technology, allowing for seamless integration into a home’s audio system. This technology helps in achieving a wider soundstage and better imaging, making it perfect for both music and movie experiences.

Moving up to the CM6HD, the larger 6.5-inch woofer enhances bass response, providing a richer audio experience. Its 1-inch pivoting soft dome tweeter allows for customizable sound direction, ensuring that listeners get the most immersive audio experience possible. The CM6HD also features a unique magnetic grille that allows for easy installation and discreet appearance, ensuring that the aesthetic of any room remains intact while still enjoying exceptional sound quality.

The CM8HD is the flagship model of the series, designed for audiophiles seeking the ultimate performance. With an 8-inch woofer and dual 1-inch tweeters, this speaker is built to fill larger spaces with powerful, full-bodied sound. The CM8HD includes Niles Audio’s advanced dual voice coil technology, offering flexibility in audio performance. Its optimized tweeter placement means that users can enjoy sound that is evenly distributed throughout the room, making it perfect for larger home theaters or entertainment spaces.

All models in the CM series feature a weather-resistant design, making them suitable for indoor and outdoor installations. Niles also offers customizable paintable grilles that allow these speakers to blend seamlessly into any décor. Additionally, each model incorporates advanced high-definition sound reproduction capabilities, ensuring that high-resolution audio files are played back as intended.

In conclusion, the Niles Audio CM5HD, CM6HD, and CM8HD in-ceiling speakers combine cutting-edge technology with elegant designs. With features that enhance sound quality, user flexibility, and aesthetic appeal, these speakers are perfect for anyone looking to elevate their audio experience in any environment, proving that great sound can be enjoyed without sacrificing style.
Top Page Image Contents