B-18 / ENGLISH

CHARGING WET BATTERIES

EDS - Charge the batteries each time the machine is used or when the Battery Indicator (D5) is reading less than full.

Standard - Charge the batteries each time the machine is used or when the Battery Indicator (J1) is flashing RED.

WARNING!

Do not fill the batteries before charging.

Charge batteries in a well-ventilated area.

Do not smoke while servicing the batteries.

When Servicing Batteries...

*Remove all jewelry

*Do not smoke

*Wear safety glasses, rubber gloves and a rubber apron

*Work in a well-ventilated area

*Do not allow tools to touch more than one battery terminal at a time

*ALWAYS disconnect the negative (ground) cable first when replacing batteries to prevent sparks.

*ALWAYS connect the negative cable last when installing batteries.

If your machine shipped with an onboard battery charger do the following:

Turn the Key Switch (A) OFF. Unwind the electrical cord from the side of the onboard charger and plug it into a properly grounded outlet. Refer to the OEM product manual for more detailed operating instructions.

If your machine shipped without an onboard battery charger do the following:

Disconnect the batteries from the machine and push the connector from the charger into the Battery Pack Connector (18). Follow the instructions on the battery charger. SERVICE NOTE: Make sure you plug the battery charger into the connector with the handle attached to it.

CAUTION!

To avoid damage to floor surfaces, wipe water and acid from the top of the batteries after charging.

CHECKING THE BATTERY WATER LEVEL

Check the water level of the batteries at least once a week.

After charging the batteries, remove the vent caps and check the water level in each battery cell. Use distilled or demineralized water in a battery filling dispenser (available at most auto parts stores) to fill each cell to the level indicator (or to 10 mm over the top of the separators). DO NOT over-fill the batteries!

CAUTION!

Acid can spill onto the floor if the batteries are overfilled.

Tighten the vent caps. Wash the tops of the batteries with a solution of baking soda and water (2 tablespoons of baking soda to 1 liter of water).

CHARGING GEL (VRLA) BATTERIES

EDS - Charge the batteries each time the machine is used or when the Battery Indicator (D5) is reading less than full.

Standard - Charge the batteries each time the machine is used or when the Battery Indicator (J1) is flashing RED.

WARNING!

Charge batteries in a well-ventilated area.

Do not smoke while servicing the batteries.

When Servicing Batteries...

*Remove all jewelry

*Do not smoke

*Wear safety glasses, rubber gloves and a rubber apron

*Work in a well-ventilated area

*Do not allow tools to touch more than one battery terminal at a time

*ALWAYS disconnect the negative (ground) cable first when replacing batteries to prevent sparks.

*ALWAYS connect the negative cable last when installing batteries.

CAUTION!

Your voltage regulated lead acid (VRLA) battery will deliver superior performance and life ONLY IF IT RECHARGED PROPERLY! Under or overcharging will shorten battery life and limit performance. Be sure to FOLLOW PROPER CHARGING INSTRUCTIONS! DO NOT ATTEMPT TO OPEN THIS BATTERY! If a VRLA battery is opened, it loses its pressure and the plates become oxygen contaminated. THE WARRANTY WILL BE VOIDED IF THE BATTERY IS OPENED.

If your machine shipped with an onboard battery charger do the following:

Turn the Key Switch (A) OFF. Unwind the electrical cord from the side of the onboard charger and plug it into a properly grounded outlet. Refer to the OEM product manual for more detailed operating instructions.

If your machine shipped without an onboard battery charger do the following:

Disconnect the batteries from the machine and push the connector from the charger into the Battery Pack Connector (18). Follow the instructions on the battery charger. SERVICE NOTE: Make sure you plug the battery charger into the connector with the handle attached to it.

IMPORTANT: Make sure you have an appropriate charger for use on Gel cell batteries. Use only “voltage-regulated” or “voltage-limited” chargers. Standard constant current or taper current chargers MUST NOT be used. A temperature-sensing charger is recommended, as manual adjustments are never accurate and will damage any VRLA battery.

B-18- FORM NO. - 56041684 - BA 755, BA 855

Page 40
Image 40
Nilfisk-Advance America 56315047(855 EDS) manual 18 / English, Charging WET Batteries, Checking the Battery Water Level

56315047(855 EDS), 56315043(755C), 56315042(755), 56315045(755 EDS), 56315044(855) specifications

Nilfisk-Advance America is renowned for its high-quality cleaning solutions, and among its impressive lineup, the models 56315046 (755C EDS), 56315044 (855), 56315045 (755 EDS), 56315042 (755), and 56315043 (755C) stand out for their performance and innovation. These machines are designed to meet the needs of various industrial cleaning applications, combining advanced technology with user-centric features.

The 56315046 (755C EDS) is a compact and highly efficient ride-on scrubber dryer equipped with Nilfisk's Enhanced Floor Cleaning System (EDS). This technology enables an exceptional cleaning performance by optimizing water usage and enhancing chemical application, resulting in cleaner floors with reduced detergent use. Its ergonomic design ensures operator comfort and ease of use, making it ideal for cleaning large areas in warehouses, distribution centers, and retail spaces.

The 56315044 (855) model is a robust, durable floor scrubber that is particularly suited for heavy-duty environments. It features a versatile scrub deck that can tackle different floor surfaces, ensuring thorough cleaning without damaging delicate materials. The machine’s intuitive controls allow for easy operations, even for less experienced staff, thus minimizing training time. Its high-capacity tank ensures extended run times, which boosts productivity in larger facilities.

In contrast, the 56315045 (755 EDS) offers similar EDS technology but in a more compact form factor, making it easier to navigate tighter spaces. This model achieves a powerful clean while maintaining energy efficiency, thanks to its advanced brushless motor that reduces wear and tear while extending the machine's lifecycle. The 56315042 (755) similarly provides a strong cleaning solution but focuses on simplicity and reliability, perfect for day-to-day cleaning tasks in various industrial applications.

Finally, the 56315043 (755C) combines the ergonomic benefits of a ride-on design with the robust features seen in the other models. It incorporates user-friendly controls, allowing operators to adjust settings quickly, optimizing performance based on cleaning requirements. Equipped with superior suction capabilities, it guarantees quick drying times, minimizing slip hazards in busy environments.

Each model in the Nilfisk-Advance America lineup showcases a commitment to quality, efficiency, and user comfort, making them vital assets for any facility aiming to maintain cleanliness and hygiene standards.