Manuals / Nimbus Water Systems / Household Appliance / Water System

Nimbus Water Systems WM5-50 System Activation and Flushing, System Activation and Inspection

Models: WM5-50

1 9
Download 9 pages 2.51 Kb
Page 7
Image 7

System Activation and Flushing

System Activation and Inspection

1.Check all tubing connections to ensure they are firmly seated. CHECK TO SEE THAT THE CARTRIDGE RETAINER CLIP IS PROPERLY ENGAGED AND LOCKED. Failure to keep the retaining clip in place will result in accidental leaks and flooding.

2.Open the dispensing faucet at the sink. Close the tank shut-off valve.

3.Open the feed water valve to the system. Observe all tubing and connections for several minutes to detect any leaks. In approximately 5 minutes, (assuming normal feed water pressure) the dispensing faucet should begin dripping.

4.Place a pan or other temporary­ water basin near the drain 'P' trap. Loosen the connector nut holding the 3/8" tube in the drain saddle connec­tor. Pull the tube out of the connector and use the pan to catch any water that may spill. Brine water should be flowing from the tube. Reconnect the tube to the drain saddle and hand-tighten­ the connector nut.

5.Allow the faucet the run for up to 15 minutes, then close the faucet.

6.Check for leaks at all connections.

7.Open the tank shut-off valve.

Initial Flushing Procedure

1.Before the system can be used for drinking water production it must be adequately flushed. Each reservoir tank is dosed with a small amount of powdered sanitizer before shipment, typically a chlorinating agent, in order to ensure tank internal cleanliness. Also, the carbon filter cartridge will release a small amount of carbon fines during the first tankful of flow. This flushing procedure will allow any sanitizer or carbon fines to pass from the system.

2.Initial tank filling will take approximately one hour (based on average feed pressure). When the tank is full, the water pressure will have risen to the point where the automatic shut-off valve inside the system will stop the feed flow through the system. Actuation of the automatic shut-off valve can be determined by either checking for a lack of brine flow to the drain saddle, or by listening very closely near the dispensing faucet for absence of water flow sound though the air gap.

When the tank has filled for the first time, it should be left undisturbed for at least 8 hours to ensure proper sanitization.

3.After 8 hours has elapsed, open the dispensing faucet fully and allow the product water to run out to drain at maximum flow. The initial discharge will be dark with the bulk of the carbon particle wash out. There may also be the scent of chlo- rinated water from the sanitizing agent. When the flow has diminished to a fast drip or small stream, close the dispensing faucet.

4.Fill and flush the tank at least three times prior to use. If necessary, repeat until the chlorination scent has disappeared. It is important that the flush be done at maximum flow (e.g. the tank must be full) to assist in rapid wash out. After this flushing procedure the system is ready for normal use.

41840-A McAlby Court, Murrieta, CA 92562

7

(800) 451-9343, email: sales@nimbuswater.com

 

Page 6 Page 8
Page 7
Image 7
Nimbus Water Systems WM5-50 System Activation and Flushing, System Activation and Inspection, Initial Flushing Procedure
Page 6 Page 8

WM5-50 specifications

The Nimbus Water Systems WM5-50 is an advanced water filtration system designed for both residential and commercial applications. This innovative unit combines cutting-edge technology with user-friendly features, making it an ideal choice for those seeking clean and safe drinking water.

One of the standout features of the WM5-50 is its multi-stage filtration process. This system utilizes a combination of sediment filters, activated carbon filters, and reverse osmosis membranes, ensuring that a wide range of contaminants are effectively removed from the water. This not only enhances the taste and odor of the water but also ensures that harmful substances such as heavy metals, chlorine, and bacteria are eliminated.

Another key characteristic of the WM5-50 is its high purification capacity. With a production rate of up to 50 gallons per day, this system is well-suited for larger households or small businesses that require a consistent supply of purified water. The efficient design minimizes water waste, making it an environmentally friendly option as well.

The WM5-50 also features smart technology for easy monitoring and maintenance. An intuitive LED display provides real-time information on filter status and water quality, alerting users when it's time for replacements or maintenance. This feature reduces the hassle of upkeep and ensures that the system consistently operates at peak efficiency.

Additionally, the Nimbus Water Systems WM5-50 includes a compact design that allows for convenient installation under sinks or in utility areas. The space-saving design does not compromise its performance, ensuring that users receive high-quality filtered water without sacrificing valuable storage space.

In terms of durability, the materials used in the WM5-50 are of high quality, ensuring long-lasting performance. The system is built to withstand varying water pressures and conditions, making it reliable in various environments.

In conclusion, the Nimbus Water Systems WM5-50 is a comprehensive water filtration solution that combines advanced features with user-friendly technology. From its multi-stage filtration process to smart monitoring capabilities and efficient design, this system is engineered to provide safe, clean, and refreshing water for all your needs. With the WM5-50, you can enjoy peace of mind knowing that your drinking water is pure and free from contaminants.