4.Slide the Grounding Bracket (136) onto one of the Handrail Spacers (92) in the location shown.
See inset drawing A. Pinch the tabs on the Grounding Bracket (136) so that the tabs will fit into the hole in the Upright (83) (see inset drawing B).
See inset drawing B. Place the Handrail Spacer (92) on the left Upright (83) as shown, with the cutout on the indi- cated side. Note: Make sure that the tabs on the Grounding Bracket (136) (see inset drawing A) are in- serted into the hole in the left Upright.
4 | 136 | 92 | A |
| Tabs | ||
|
|
| 136 |
B |
|
| Cutout |
|
|
| |
| 92 |
| 83 |
|
|
|
5. Place one of the Handrail Spacers (92) on the right | 5 |
| A |
|
Upright (83) as shown, with the cutout on the indicated |
|
| ||
79 |
| Cutout | ||
side (see inset drawing A). Pull the Upright Wire Harness |
| |||
|
|
|
| |
(131) up through the cutout. Place the other Handrail |
|
|
|
|
Spacer on the left Upright (not shown). |
|
| 92 |
|
|
|
|
| |
Have a second person hold the Handrails (73) near the |
| 73 |
|
|
Uprights (83) as shown. Connect the Upright Wire |
|
| B |
|
Harness (131) to the wires extending from the right | 131 | 83 | 131 | |
Handrail. Insert the connectors and the Upright Wire |
| |||
|
|
|
| |
Harness (131) into the opening in the Console Base (79) |
|
|
|
|
(see inset drawing B). |
|
|
|
|
Set the Handrails (73) on the Handrail Spacers (92), | 92 |
|
|
|
|
|
|
| |
being careful not to pinch the Wire Harness (131). |
|
|
| 79 |
6. Insert two Handrail Bolts (96) with Handrail Washers | 6 |
|
|
|
(95) and Handrail Bushings (94) into the right Upright |
|
|
| |
|
|
|
| |
(83) and the right Handrail Spacer (92). Turn the |
|
| 73 |
|
Handrail Bushings (94) so they fit against the Upright as |
|
|
| |
|
|
|
| |
shown in the inset drawing. Lift up the right Handrail |
| 92 |
| |
(73) and align the Bolts with the holes in the Handrail. |
|
| ||
|
| 83 |
| |
Next, thread the Bolts into the Handrail. Do not tighten |
|
|
| |
the Bolts yet. |
|
| 94 | |
Attach the left Handrail (not shown) in the same way. |
|
|
| 95 |
|
|
|
| |
Tighten all four Handrail Bolts (96). |
|
|
|
|
| 94 | 95 |
| 96 |
|
|
| ||
7.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or carpet from damage, place a mat under the treadmill.
7
