North Star 8000 IPG PRE-START Preparations, Starting Manual, Starting Electric, Operating Speed

Toaster	1000
Vacuum cleaner	250
VCR	70
Water Heater	3000
Weed Trimmer	500

(a)Hard-starting motors require 3 to 5 times the rated running watts.

(b)These loads may require up to 15 minutes to restart due to its normal build up of compressor head pressure.

NOTE: For extremely hard to start loads such as air conditioners and air compressors, consult the equipment dealer to determine the maximum wattage.

PRE-START PREPARATIONS

Your generator has been thoroughly tested prior to shipment from the factory. However, damage can occur during shipping, so be sure to check for damaged parts or loose or missing nuts and bolts. If problems occur, call Customer Service at 1-800-270-0810.

GROUNDING - All units must be grounded. Drive a 3/4” or 1” copper pipe or rod into the ground close to the generator. The pipe/rod must penetrate moist earth. Connect an approved ground clamp to the pipe. Run a no. 12 Ga. wire from the clamp to the generator grounding post located on the control panel. Do not connect to a water pipe or a ground used by a radio system.

CAUTION: The engine has been shipped without oil. Fill the crankcase with oil before trying to start. Low oil shutdown prevents your generator from starting without sufficient oil.

OPERATING SPEED

The generator must be run at the correct speed in order to produce the proper electrical voltage and frequency. The speed of the engine was carefully adjusted at the factory so that the generator produces the proper voltage and frequency.

The output voltage should be checked to ensure the generator is working properly before connecting a load to the generator. Failure to do so could result in damage to equipment plugged into the unit and possible injury to the individual.

All engines have a tendency to slow down when a load is applied. When the electrical load is connected to the generator, the engine is more heavily loaded, and as a result the speed drops slightly. This slight decrease in speed, together with the voltage drop within the generator itself, results in a slightly lower voltage when the generator is loaded to its full capacity than when it is running with no load. The slight variation has no appreciable effect in the operation of motors, lights and most appliances. Electronic equipment and clocks will be affected if correct RPM is not maintained. See Load vs. Output chart.

Load			Output
Percent of	Speed		Frequency	Generator
Generator	(RPM)		(Hz)	Voltage at 120V
Output				Receptacle
0 %	3780		63.0	129V
50 %	3600		60.0	120V
100 %	3480		58.0	112V
Output	voltage	should periodically be checked to

ensure continued proper operation of the generating plant and appliances, it can be checked with a portable meter. Frequency can be checked using an electric clock with a sweep second hand. Timed against a wristwatch or a stopwatch the clock should be correct within +/- 2 seconds per minute. A qualified technician should do all speed setting adjustments.

BEFORE STARTING

1.Make sure the generator is positioned on firm level surface.

2.Check the crankcase for oil and maintain at a proper

level.

3.Check fuel level and fill tank with fresh unleaded gasoline. Never fill fuel tank completely to the top. Always wipe up and remove any spilled gasoline.

4.Make sure that the exhaust fumes are directed away from people.

STARTING - MANUAL

1.Disconnect all loads to generator.

2.Turn gas line valve to ON position.

3.Turn key to the ON position.

4.For cold engine, move choke lever to full choke position, for warm engine, move choke lever to half choke or to RUN position.

5.Firmly grasp recoil handle and pull.

6.When engine starts, move choke lever to RUN position.

7.Loads may now be connected to generator.

STARTING - ELECTRIC

1.Disconnect all loads to generator.

2.Turn gas line valve to ON position.

3.For cold engine, move choke lever to full choke

position, for warm engine, move choke lever to half choke or to RUN position.

4. Turn key to start position.

8