WIRING

All wiring must comply with local and national codes and unit must be properly grounded.

1.Run 120VAC, 60Hz supply wiring to the wall switch (not provided). The unit must be wired on a separate 20

Amp circuit.

2.Run wiring from the switch to the housing junction box. Loosen screw holding exterior wiring compartment cover and remove cover. Interior wiring compartment cover can be removed if necessary by loosening screw in keyhole slot. Remove knockout(s) as required and install approved box connectors.

3.Refer to Fig. 2. Connect white wires in junction box to white (neutral) supply wire. Connect the blue wire from the two wire receptacle to the supply wire from the vent switch. Connect the red wire in the junction box from the three pin receptacle to the supply wire from the heat switch. Connect both green ground leads in the junction box to the supply ground.

4.Replace wiring compartment cover and tighten screw to secure.

5.Insert vent motor plug in black receptacle on wiring compartment cover. Insert plug from heater assembly into the white receptacle on the wiring compartment cover.

HEATER JUNCTION BOX

 

VENT

HEAT

RECEPTACLE

RECEPTACLE

 

GREEN

WHITE

 

WHITE

 

BLUE

 

RED

WALL SWITCH BOX

 

VENT

 

HEAT

 

WHITE

 

BLACK

SUPPLY

 

 

GROUND

SWITCH SHOWN IS NUTONE

 

ACCESSORY SWITCH HS-91

 

(SOLD SEPARATELY)

 

120VAC LINE

FIGURE 2

 

DUCTING

1.Snap plastic duct adapter and damper assembly over flanged opening on housing. Connect 4" round duct to the duct adapter and secure with duct tape. The duct should be run to the outside of the structure through a roof or wall cap. For maximum performance keep duct runs as short and as straight as possible.

MOUNTING THE GRILLE

1.Position grille over housing.

2.Insert grille mounting bracket into slots in grille center opening.

3.Insert 1" screw through the hole in the center of the mounting bracket and thread it into the center hole in the housing cross bar. Tighten the screw just enough to hold the grille firmly against ceiling. Snap cover over rectangular opening in center of grille.

FIGURE 3

COVER

FIGURE 4

Page 1 Page 3
Page 2
Image 2
NuTone 605RP installation instructions Wiring, Ducting, Mounting the Grille, Amp circuit
Page 1 Page 3

605RP specifications

The NuTone 605RP is a versatile and efficient ventilation fan designed to meet the needs of those seeking a reliable solution for indoor air quality. Known for its powerful performance and quiet operation, the 605RP is an excellent option for bathrooms, utility rooms, or any space requiring enhanced air circulation.

One of the standout features of the NuTone 605RP is its robust airflow capacity. With a rating of 50 CFM (cubic feet per minute), this fan effectively removes moisture and unwanted odors, helping to maintain a fresher and healthier environment. This airflow capability is particularly important in areas prone to humidity, such as bathrooms, where excess moisture can lead to mold and mildew growth.

Another key technology integrated into the 605RP is its low-noise operation. Operating at a sound level of only 2.5 sones, this ventilation fan ensures a quiet atmosphere, allowing users to maintain peace and comfort in their spaces. This feature is especially beneficial during nighttime use or in homes where noise levels need to be kept to a minimum.

The design of the NuTone 605RP is another aspect that enhances its appeal. It features a sleek and unobtrusive look that fits seamlessly into a variety of decors. Additionally, the fan comes with an easy-to-install housing, making it a user-friendly option for both contractors and DIY enthusiasts.

The durable construction of the 605RP is also noteworthy. Made from high-quality materials, this fan is built to last, reducing the need for frequent replacements and maintenance. Its energy-efficient design helps in lowering electricity consumption, making it an environmentally friendly choice.

Installation is made simple with the fan’s adjustable mounting brackets, allowing for flexible placement in different ceiling types. The 605RP is compatible with a variety of ducting options, enabling users to customize their setup according to their specific needs.

In summary, the NuTone 605RP serves as an excellent choice for anyone looking for an effective and quiet ventilation solution. With its powerful airflow, low-noise operation, durable construction, and user-friendly design, it stands out as a reliable option for enhancing indoor air quality and comfort.
Top Page Image Contents