Quick Reference | CM 1830 Cash Register | 5/621/3300 (13) |
Error messages: operation
Error messages appear in the display and an acoustic signal is issued as a result of incorrect operation.
6 | Error message is cleared |
|
|
|
Error | Cause | Error | Cause | |
message |
| message |
| |
E00 | Incorrect key pressed | E60 |
| The item barcode is valid but not found in the PLU |
E01 | Incorrect key operation sequence |
|
| database. |
E02 | A number/digit sequence (with decimal point) must be | E61 |
| This item has been withdrawn from sales |
| entered or the entry is too long | E62 |
| This department has been withdrawn from sales |
E03 | Result exceeds permitted number of digits or is zero | E63 |
| Discount is possible for this PLU registration |
E04 | Result exceeds permitted number of digits or is zero | E64 |
| The PLU index is outside the range |
|
| E65 |
| The number of digits permitted for price entry for |
E10 | Incorrect key pressed |
|
| departments has been exceeded |
|
| E70 |
| It is not necessary to enter the clerk code |
E20 | Card payments related to negative values are not | E71 |
| The clerk code entered exceeds four digits |
| accepted | E72 |
| The clerk code is incorrect |
E24 | Electronic |
|
|
|
E30 | This operation must be performed within a registration | E80 |
| The input must be positive or zero |
E31 | This operation must be performed outside a registration | E81 |
| The item barcode was not found / recognized |
E32 (ÁÇÅÅ ) | PLU number in the registration outside the range | E82 |
| The result exceeds the range |
E33 | PLU in the registration could not be found | E83 |
| The sum exceeds the range |
|
| E84 |
| The counter for the validation printout exceeds the |
E40 | The operation requires the input of a number |
|
| permissible value |
E41 | The operation does not require the input of a number | ¿ÊËÂÀ¸ÁÇÅÅ | The total amount in the cash register drawer exceeds the | |
E42 | The operation accepts the input of a zero |
|
| permissible value |
E43 | The number entered exceeds the range | E86 |
| Operating mode R/T has been changed |
E44 | The digits entered exceeds the range for PLU input | E87 |
| Price input zero has been blocked |
E45 | Result cannot be rounded | E88 |
| Compulsory to enter the change |
E46 | Result cannot be rounded | E89 |
| Pay out amount is greater than the amount in the cash |
E47 | The maximum permissible amount for checks has been |
|
| drawer |
| exceeded |
|
|
|
E48 | The percentage value is outside the range | E90 | º¸ÆÄ | Printer fault (jam) |
|
| E91 | º¸ÆÁ | Printer memory is full |
E50 | The operation does not accept the entry of a decimal | E92 |
| A fixed key cannot be reprogrammed |
| point |
|
|
|
E51 | The decimal point has already been entered | Å»½ |
| Clerk code must be entered, up to four digits |
|
| ſ½ | Language change when entering the language code | |
E52 | The number of decimal places for percentage input |
|
| Caution! |
| exceeds 2 |
|
| All settings will be lost! |
|
| Ï¹É |
| Change keyboard assignment |
Only enter the following when you are familiar with the programming functions!
Caution:
Set the key to position P
After pressing the following key combination, the daily sales, grand total and all programmed settings (departments, PLUs, Flags etc.) are deleted.
k | ¿Å¹Ê¸ appears in the display |
y | All programmed settings and sales figures are deleted |
After pressing the following key combination, all the programmed settings (departments, PLUs, etc.) are deleted and reset to their "default state".
U | À¹ÁÊÇżappears in the display |
y | The department and PLU prices are reset |
After pressing the following key combination, the grand total is reset. It is only executed when the Full
s | ¿Å¹Ê¸ appears in the display |
y | The grand total is deleted |
|
|
Olympia 09.2001 | Page 10 | All rights reserved. |