Omega EP95 Important User Information, Usage Suggestions for Omega Vapor Steam Cleaner

USAGE SUGGESTIONS FOR OMEGA VAPOR STEAM

CLEANER

ADDITIONAL IMPORTANT SAFEGUARDS cont.

Important User Information

Please note that this steam cleaner has a “flow through injection” type boiler and is not a pressurized system. It will take approximately 45-90 seconds for the steam injector to heat up and the “steam ready light” to go off. Once the steam ready light has gone off, push the steam switch on the handgrip to the “On” position (I) in order to start the steam flow. Steam power will steadily increase during the first four (4) minutes of use, after which time steam output will stabilize. Some steam will condense around the floor brush when in use and will cause hard surfaces to become wet during the cleaning process, this

is normal.

1.To avoid circuit overload, do not operate another appliance on the same socket (circuit) when using this unit.

2.If an extension cord is absolutely necessary, a 15 ampere 14 gage cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange cord so that it cannot be pulled or tripped over.

3.Do not leave unattended when the system is connected to a power supply/electrical outlet.

Warning: Always keep unit in upright position when in use. Do not lie flat on the floor or turn upside down when in use. Inverting the unit or placing flat on the floor may cause hot water to exit from the hose and cause injury.

Note: We recommend that you drain the water tank after every use.

Tips On How To Use Your System

Water

•Use tap water for all your cleaning needs, however, if you live in an area with hard water, use demineralized/distilled water.

Important: Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance. Use tap water or distilled/purified water if the tap water in your area is very hard.

Temperature

•The vapor temperature at the tip of

the nozzle is between 220°F and 240°F.

•The temperature of the vapor falls to 100 °F at a distance of 10 inches from the nozzle.

CAUTION: A towel wrapped around the brush can become hot enough to burn. Make sure that you let the towel cool off before touching it or changing it.

Using Towels

Note: We strongly recommend the use of two (2) 100 % cotton towels layered one on top of the other.

•For best results use 100% cotton white terry cloth towels.

•Use correct size (8” x 17”) of towel to allow you to wrap the towel over the ends of the brush and clip it under the spring loaded towel clips.

•The purpose of using towels is to absorb the moisture and dirt being removed. Always use dry towels. A wet towel will smear the dirt.

•Wash towels with strong detergent and bleach.

9

•Using scented fabric softener while washing the towels will cause the scent to be released into the air when using the towels with your steam system.

Wood, Vinyl and Marble Floors

Use the floor brush with a 100% cotton terry cloth attached, ( see page 7 for details). Move the brush slowly in back and forth motions. When the towel is soiled, you can turn the towel over or replace it with a clean towel. If you are working on a very dirty area, we recommend that you move the brush over the area slowly, several times. If it is a wood floor, do NOT leave the unit stationary for any length of time to avoid heat or moisture build-up in the wood. By cleaning with the towel over the brush, you will not affect the shine on the floor.

To Clean Waxed Floors: Install a clean towel(s) on the floor brush, work quickly. The towel will absorb the dirt but not remove the wax.

Vinyl Floors: Do not allow heat to buildup in any kind of vinyl, since it can soften it enough to affect its texture. Work quickly on vinyl. Use two (2) towels on floor brush.

Tile Floors: For tile and marble floors only, if there is an area of the floor which is excessively dirty, you may remove the towels and agitate the area with the brush bristles directly. Do not let the area dry. Wipe immediately with a clean cloth. Re- clean with brush and towels in place.

Note: Do not use steam cleaner on hardwood or vinyl floor without towels installed on the floor brush.

Caution: Upon initial use, the steam will be mixed with water, hot enough to scald. Ensure that the floor brush is resting on the floor or the hose handgrip is directed away from user when steam switch is turned on. Never direct the nozzle or brush end of the unit toward yourself or anyone near you.

Important User Information

Please note that this steam cleaner has a “flow through injection” type boiler and is not a pressurized system. It will take approximately 45-90 seconds for the steam injector to heat up and the “steam ready light” to go off. Once the steam ready light has gone off, push the steam switch on the handgrip to the “On” position (I) in order to start the steam flow. Steam power will steadily increase during the first four (4) minutes of use, after which time steam output will stabilize. Some steam will condense around the floor brush when in use and will cause hard surfaces to become wet during the cleaning process, this is normal.

Warning: This appliance is equipped with a grounded-type 3-wire cord (3-prong plug). This plug will only fit into an electrical outlet made for a 3-prong plug. This is a safety feature. If the plug should fail to fit the outlet, contact an electrician to replace the outlet. Do not attempt to defeat the safety purpose of the grounding pin, part of the 3-prong plug.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

2