FINAL INSTALLATION

3

 

 

CONTACT MODELS

Follow the instructions below:

1.Drill a suitable hole in the vessel or pipe wall and tap for 3/4” NPT. If this walled vessel or material is not suitable for threading, weld or braze a bush- ing to accept the sensor.

2.Screw the sensor in the threaded section and make sure that there is a good seal. Use a pipe compound or sealing tape compatible with the materials and avoid excessive tightening.

3.Run the power and control wiring cable to the electronic control unit. Observing all applicable electrical codes and proper wiring procedures.

CONTROL UNIT

Refer to the typical installation diagram and control unit dimensions when installing the control unit. Follow steps 1 and 2 below for remote mounted elec- tronic units. Steps 3 through 7 are common for both the integral electronic units and remote electronic units.

1.Mount the remote control unit on any suitable wall, panel, etc. making sure there is adequate clearance for wiring.

2.Remove the PC board by removing the screws. Drill a suitable size hole in the control unit housing for a conduit fitting (if so required).

3.Remove the cover from housing. To complete wiring, either leave or remove the electronics printed circuit board in the housing on remote units and remove the encapsulate electronics in integral units.

CAUTION: Never remove unit from a vessel with power and/or output control cables connected to the electronic control unit inside the housing to avoid cable damage.

4.Wire the unit as desired. Refer to the wiring diagram inside the cover.

Note: All wiring, conduit and fittings should conform to local electrical codes. In a hazardous location, a conduit seal should be installed within 18 inches of the control unit housing. Use a drain seal in vertical conduit run to prevent condensation from entering the control unit. OMEGA assumes no responsibility for improperly wired units.

5.Replace the printed circuit board, if removed, or the encapsulated electronics. Make certain that the wires are dressed carefully to prevent pinching between the cover and the housing.

6.Replace the housing cover.

6For Ultrasonic Point Level Switches

Page 7
Image 7
Omega Speaker Systems LVUC10, LVU-260, LVU-230 manual Final Installation, Contact Models, Control Unit

LVU-230, LVUC10, LVU-260 specifications

The Omega Speaker Systems LVU-260, LVUC10, and LVU-230 are exemplary audio solutions that stand out in the competitive landscape of sound systems. These speakers are designed to deliver a powerful audio experience, making them ideal for a variety of settings, from home theaters to professional audio applications.

The LVU-260 is a high-performance, two-way speaker known for its impressive sound clarity and robust construction. It features a 6.5-inch woofer that provides deep bass response, while the 1-inch silk dome tweeter ensures crystal-clear high frequencies. The LVU-260 is equipped with an innovative frequency crossover that allows seamless integration between its components, resulting in a well-balanced sound profile. With a power handling capacity of up to 150 watts, it can be used in larger spaces without compromising audio quality.

On the other hand, the LVUC10 offers versatility and convenience with its compact design. This speaker is particularly popular for smaller living spaces and portable applications. The LVUC10 features a 5-inch woofer and a 1-inch tweeter, achieving a compelling sound signature that belies its size. It incorporates advanced technologies such as a built-in digital amplifier, which maximizes efficiency while providing a dynamic range that can adapt to varied listening environments. Its lightweight and compact design make it easy to position and set up, making it an excellent choice for on-the-go audiophiles.

Lastly, the LVU-230 combines style and performance, featuring a sleek cabinet design that seamlessly integrates into any decor. It utilizes a coaxial driver configuration, which places the tweeter directly in the center of the woofer, allowing for superior sound staging and imaging. The LVU-230 is also designed with acoustic suspension technology, which enhances bass response while minimizing distortion, resulting in a clear and focused audio experience. With a frequency response range that extends from 45 Hz to 20 kHz, this speaker is capable of catering to a wide array of musical genres.

Each model in the Omega Speaker Systems lineup is built with durability and performance in mind, utilizing top-notch materials and engineering techniques. With these speakers, users can expect exceptional sound quality that elevates their audio experience, whether they are watching movies, listening to music, or engaging in gaming. The Omega Speaker Systems LVU-260, LVUC10, and LVU-230 are truly remarkable options for anyone looking to enhance their sound system.