Connecting the speakers

For safety reasons, do not turn on any devices or components until you have completed all wiring procedures.

■Connecting the satellite speakers

Note:

The nominal impedance of this speaker system is 6 Ω . Use only amplifiers capable of handling this impedance.

Front right

Center

Front left

speaker

speaker

speaker

MODEL D-L1

(RED)

MODEL D-L1

(GRN)

MODEL D-L1

(WHT)

Green

Red

White

Surround right

 

Surround left

speaker

SURROUND

speaker

 

 

SPEAKERS

FRONT SPEAKERS

 

 

 

R L

R CENTER L

 

MODEL D-L1

(GRY)

 

MODEL D-L1

(BLU)

Gray

 

 

 

 

 

 

 

 

 

Blue

 

 

 

L

 

ANTENNA

SURROUND

FRONT SPEAKERS

 

PREOUT

 

 

 

 

 

R

L

R

CENTER

L

AC INLET

AUDIO

 

 

REMOTE

 

ANTENNA

 

 

 

 

 

 

 

 

 

CONTROL

 

 

 

 

 

 

 

 

 

 

R

 

AM

FM 75

 

 

 

 

 

SUB

IN

OUT

IN

 

 

 

 

 

 

 

 

WOOFER

TV/LINE

MD/CDR/TAPE

 

 

 

 

 

 

 

 

DIGITAL

 

VIDEO OUTPUT

 

 

 

 

 

 

 

OPTICAL

 

Y

P

P

 

 

 

 

 

 

OUT

IN

S VIDEO

VIDEO

COMPONENT

 

 

 

 

 

 

 

Before connecting
Prepare the supplied speaker cables as shown below.

Strip off the end of the

Twist together the exposed

speaker cable insulation.

wires strands.

Connecting to the speaker terminals

Push down the lever.

Insert the

Release the lever.

 

exposed wires

 

 

into the hole.

 

•Connect the input terminals on the rear of the satellite speakers to the speaker output terminals on the AV amplifier or receiver using the supplied speaker cables as shown in the diagram to the left.

•Each speaker cable should be connected to the speaker terminal of the same color.

The speaker’s terminals are colored as follows.
Front left speaker (+): white
Front right speaker (+): red
Center speaker (+)

: green

Surround left speaker (+): blue
Surround right speaker (+): gray

Notes:

• Make sure that the positive (+) and negative (–) speaker cables do not contact each other. If they do, a short-circuit may occur, causing damage to the amplifier.

•Be sure to connect the speaker cables with the correct polarity (+ and –) and with the proper left-right speaker orientation. If connected incorrectly, the resulting sound space with sound unnatural.

•Pull the speaker cable lightly to ensure that it is connected firmly.
■Connecting the subwoofer

When used together with an AV amplifier or receiver with surround playback capabilities, be sure to connect its SUB WOOFER PREOUT terminal to the subwoofer SL-105 using the supplied pin-cord.

If you connect the subwoofer SL-105 using speaker cables, depending on the settings at the AV amplifier or receiver, bass signals may be cut for an unsatisfactory bass output. For more details regarding connection procedures, refer to the manuals that came with your AV amplifier or receiver.

 

 

 

L

 

ANTENNA

SURROUND

FRONT SPEAKERS

 

PREOUT

 

 

 

 

 

R

L

R

CENTER

L

AC INLET

AUDIO

 

 

REMOTE

 

ANTENNA

 

 

 

 

 

 

 

 

 

CONTROL

 

 

 

 

 

 

 

 

 

 

R

 

AM

FM 75

 

 

 

 

 

SUB

IN

OUT

IN

 

 

 

 

 

 

 

 

WOOFER

TV/LINE

MD/CDR/TAPE

 

 

 

 

 

 

 

 

DIGITAL

 

VIDEO OUTPUT

 

 

 

 

 

 

 

OPTICAL

 

Y

P

P

 

 

 

 

 

 

OUT

IN

S VIDEO

VIDEO

COMPONENT

 

 

 

 

 

 

 

PREOUT

 

 

(Supplied pin-cord)

AUDIO

 

 

 

 

SUB

 

 

 

 

WOOFER

 

 

 

 

SPEAKER LEVEL

LINE

AUTO STANDBY

+ R _

_ L

INPUT

 

+

 

INPUT

 

 

 

 

FROM

 

 

 

 

AMP/RECEIVER

 

 

L

 

 

 

 

 

 

 

 

(MONO)

 

 

 

 

 

OFF ON

OUTPUT

_

_ L

R

 

TO SPEAKERS

 

+ R

+

 

Connect the SUB WOOFER PREOUT terminal on your AV amplifier or receiver to the subwoofer rear panel using the supplied pin-cord as shown in the diagram above.

Note:

If the amplifier has a subwoofer terminal, since its output is monaural, connect it to the low level LINE INPUT L(MONO) terminal on the subwoofer SL-105.

6