Connections (TX-SR700/700E)

Video output

S Video output

Video input

S Video input

7.DVD recorder, other digital video recording device (VIDEO 2)

L (white)

Analog audio input R (red)

L (white)

Analog audio output R (red)

8. TV monitor or projector

(MONITOR OUT)

 

ANTENNA

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPONENT VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

INPUT 2

INPUT 1

OUTPUT

 

 

Y

 

 

 

 

 

 

R

L

 

 

 

 

Y

 

 

 

FM

 

AM

 

PHONO IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

75

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PB

 

PB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PR

CONTRO

PR

Component video

 

 

 

 

 

 

 

 

 

 

 

 

REMOT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

input

DIGITAL INPUT

DIGITAL

VIDEO 3

VIDEO 2

VIDEO 1

DVD

MONITOR

 

ZONE

 

 

 

 

OUTPUT COAXIAL

IN

OUT

IN

OUT

IN

IN

OUT

 

 

 

 

OPTICAL

OPTICAL

 

 

 

 

 

 

 

 

V

 

 

 

2

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

 

 

Video input

 

 

 

COAXIAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DIGITAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

 

 

IN

OUT

IN

IN

OUT

IN

OUT

IN

FRONT

SURR

CENTER

 

S Video input

 

L

 

 

 

 

 

 

 

 

L

 

 

 

SUBWOOFER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRE OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SUB

 

 

 

CD

TAPE

VIDEO 3

VIDEO 2

VIDEO 1

 

 

 

 

 

 

 

WOOFER

 

 

DVD

: Signal flow

7.Connecting a DVD recorder or other digital video recording device (VIDEO 2)

Using RCA video cables, connect the video output jack (composite) of the device to the VIDEO 2 VIDEO IN jack of the TX-SR700/ 700E and connect the video input jack of the device to the VIDEO 2 VIDEO OUT jack of the TX-SR700/700E. Or if the device has S video input and output jacks, using S video cables, connect the S video output jack of the device to the VIDEO 2 S VIDEO IN jack of the TX-SR700/700E and connect the video input jack of the device to the VIDEO 2 S VIDEO OUT jack of the TX-SR700/700E. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the TX-SR700/ 700E.

With the initial settings of the TX-SR700/700E, the VIDEO 2 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 54).

Using RCA audio cables, connect the audio output jacks of the device to the VIDEO 2 IN audio jacks of the TX-SR700/700E and connect the audio input jacks of the device to the VIDEO 2 OUT audio jacks of the TX-SR700/700E. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the TX-SR700/700E depending on the type of connector on the device.

With the initial settings of the TX-SR700/700E, nothing is allocated as the digital input source for VIDEO 2 (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page 53).

If the device has a digital input, connect it to the DIGITAL OUTPUT (OPTICAL or COAXIAL) jack of the TX-SR700/700E for digital recording of the signal from the digital input of the TX-SR700/ 700E.

Note:

The output from the DIGITAL OUTPUT jack of the TX-SR700/ 700E is only the digital signal input to the DIGITAL INPUT jack.

8.Connecting a television monitor or projector (MONITOR OUT)

The TX-SR700/700E is equipped with a simple Y/C separate circuit and simple Y/C mixed circuit. Since both the signal from the S VIDEO and VIDEO inputs are output to the MONITOR OUT S VIDEO output, if the television or projector is equipped with an S video input, it is unnecessary to connect the video connectors. If it is equipped with only a video input, connect it to the MONITOR OUT VIDEO output.

Using an RCA video cable, connect the video input jack (composite) of the device to the MONITOR OUT VIDEO jack of the TX-SR700/ 700E. Or if the device has an S video input jack, connect it to the MONITOR OUT S VIDEO jack of the TX-SR700/700E using an S video cable. Or if the device has component video inputs, connect them to the bank of COMPONENT VIDEO OUTPUT jacks on the TX-SR700/700E.

Note:

Note that the Setup Menu will only be displayed on the monitor connected to MONITOR OUT and not those connected to the COMPONENT VIDEO OUTPUT jacks.

20