Oreck XL7705ECB warranty Parts List, Operating Instructions, Assembly, General Information

Parts List

To assist you in identifying components of your vacuum, the parts have been numbered as follows:

Operating Instructions

Make sure disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet and press the ON(l) - OFF(O) switch on handle

1Helping Hand® handle

2On/off switch

3Cord dump

4Handle tube

5Bag stiffener

6Deflector

7Bag dock

8Carry handle

9Zipper

10Bag clip

11Headlight cover

12Front light lens

13Main bumper

14Edge brush

15Belt door

16Power cord

17Cord assembly

18Handle collar

19Connector assembly

20Carry handle clamp

21Collars

22Lower tube

23Bag clip clamp

24Scent cartridge door

25Fan housing

26Rear wheels

27Side light

28Cover

29Bag spring

30Bag pocket

31Outer bag

32Power nozzle

33Inner filter bag

34Duster loop

35Cord strain relief

		1
		2
		3
		4
	5
	6
33	7	8
		9

10

11
12
13	15
	14

		17
16
	19	18
	35
8		31
	20	30
21	22	34
	23	29
24		28
25		27
	26	14
		32

assembly when ready to operate.

Up-Position Lock

fig. 4 Place foot on power head and lean handle back gently to release lock for vacuum use. Return handle to the full upright position to engage lock.

NOTE: Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.

Carry Handle

fig. 5 Raise the carry handle located on back of the unit for easy lifting, carrying, and stair vacuuming. Lower the handle during use to eliminate obstruction.

Duster Loop

fig. 6 For convenient use of dusters, a loop has been sewn onto the outer bag. This will allow easy removal and storage of the duster.

For Easy Power Cord Storage

fig. 7 Raise carrying handle and wrap power cord around carry handle and cord dump.

fig. 8 To release cord, twist cord dump located on Helping Hand® handle 1/2 turn. Slide cord off handle (fig. 9).

Cleaner Storage

The carry handle can be used for convenient, space saving storage of cleaner. Hang cleaner by carry handle on a sturdy fastener.

Operating Recommendations

This new ORECK XL7 High-Speed Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, gets under things, and it’s SO lightweight and easy to use.

The following are a few simple suggestions regarding its operation:

1.	When inserting a new disposable paper filter dust bag—FIRST
	PUFF OUT and OPEN THE BAG.
2.	When the disposable filter dust bag is full, REPLACE IT.
3.	If at any time the machine does not pick up properly or makes an
	unusual noise, STOP OPERATION and service.
4.	Although your upright will pick up pins, paper clips, and other small
	objects, it is recommended that these be removed from the floor
	before you vacuum. Failure to do so may result in permanent
	damage to the motor suction fan and its housing.
5.	WARNING: Do not use your vacuum cleaner on damp or wet
	surfaces. This will cause damage to the vacuum cleaner and is
	dangerous to the user. Damage caused by use on wet or damp
	surfaces is not covered under warranty.
6.	REPLACE THE BELT EVERY 6 MONTHS, SCENT CARTRIDGE
	EVERY MONTH, AND MOTOR FILTER EVERY 2 MONTHS.
7.	Change the disposable filter dust bag at least once a month—even
	if it is not full! The collected dust in the dust bag can cause odor,
	attract moisture, and can affect the efficiency of the cleaner.
8.	DO NOT run the vacuum cleaner over the cord. The revolving

Assembly

fig. 1 With ON/OFF switch facing the front of the unit, align slots in handle tube with tabs in connector. Insert the handle tube into connector. Tighten collar at base of handle tube onto the connector until it locks, “snaps”.

fig. 2 Snap cord assembly into the cord clip located on the left side of

the collar. Leave excess cord at the power head to allow movement.

fig. 3 To install power cord in cord strain relief, pinch power cord together and slide approximately 1-2 inches through hole in cord strain relief. Slide power cord over clamp on cord strain relief and pull excess until power cord is tightly rested under clamp.

5

brush could damage the cord.

9. Use caution when vacuuming over area rug edges and fringe.

General Information

The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service read the instructions and keep them handy for future reference.