Transmitter’s low battery indicator (shows on the main unit)
NOTE:
Attention! Please dispose of used unit or batteries in an ecologically safe manner. 
PLACING THE TRANSMITTER OUTSIDE
The transmitter should be located in an area protected from direct sunlight and rain. Place the sensor under a covered location like a roof overhand or under the eaves. This will ensure accurate temperature readings. The transmitter comes with a wall mounting/desktop holder. When mounting on a wall, screw in place the holder
using the top and bottom holes. Then secure the transmitter in the holder. The holder is also equipped with a table stand. With the transmitter secured on the holder, retract the leg on the rear of the holder and place on a flat surface.
SPECIFICATIONS
MAIN UNIT
Recommended operating range: 0 °C to 45 °C 32 °F to 113 °F
Resolution: | 0.1°C (above |
| 1°C (below |
| 0.1°F |
| 1°F (above 100°F & below |
REMOTE SENSOR
Recommended operating range: | |
| |
RF transmission frequency: | 433 MHz |
No. of remote unit: | 1 unit |
RF transmission range: maximum 100 feet
Temperature sensing cycle: around 60 ~ 64 seconds
Power
Main unit: 4.5V, use 3 x AA 1.5V alkaline battery
Remote sensor: 3 V, use 2 x AA 1.5V alkaline battery
Weight
Main unit: 8.57 oz
Remote sensor: 3.74 oz
Dimension
Main unit: 3.78(W) x 5.71(H) x 2.20(D) inch
Remote sensor: 1.57(W) x 1.26(H) x 0.94(D) inch
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products.
If you're in the US and would like to contact our Customer Care department directly, please visit: www2.oregonscientific.com/service/support.asp
OR
For international inquiries, please visit: www2.oregonscientific.com/about/international.asp.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www.oregonscientific.com or on the warranty card for this product) for all inquiries instead.
We |
|
Name: | Oregon Scientific, Inc. |
Address: | 19861 SW 95th Place, Tualatin, |
| Oregon 97062 USA |
| |
DECLARE THAT THE PRODUCT | |
Product No.: | |
Product Name: | Remote Thermo Clock |
is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)This device may not cause harmful interference.
2)This device must accept any interference received, including interference that may cause undesired operation.
Remote Thermo Cloc k
C 2008 Oregon Scientific. All rights reserved
