RM383PA
FIG. 1
1
| 4 |
2 | 5 |
| 6 |
3 | 7 |
| 8 |
FIG. 2
| 7 |
1 | 8 |
�� | |
2 |
|
��� |
|
���������� |
|
34 5 6
Atomic Projection Clock with
Ambient Lighting
Model: RM383PA
USER MANUAL
EN
OVERVIEW
FRONT VIEW (FIG. 1)
1.LED Projection / FOCUS: adjust projected image
2.Clock with Seconds / Weekday
3.Calendar
4.SNOOZE: Press to activate snooze function / activate backlight*
5.Signal reception indicator
6.Time zone offset
7.Alarm display mode
8.Alarm 1 / 2 is ON
*when adapter is connected, backlight is continuously on.
BOTTOM VIEW (FIG. 2)
1.Battery compartment
2.PROJECTION ON / OFF: enable / disable continuous projection
3./ : Increase / decrease values of the selected setting; activate / deactivate clock reception signal
4.((.)) ALARM: View alarm status; set alarm
5.ALARM ON/OFF: activate / deactivate alarm
function
6.MODE: Change settings / display
7.AC / DC socket
8.RESET: Reset unit to default settings
GETTING STARTED
INSERT BATTERIES
1.Remove the battery compartment.
2.Insert the batteries, matching the polarities (+ /
3.Press RESET after each battery change.
CLOCK
CLOCK RECEPTION
This product is designed to synchronize its clock automatically with a clock signal.
RM383PA:
•
(Pacific, Mountain, Central or Eastern).
To enable / disable signal reception:
Press and hold | to enable or | to disable signal |
reception. |
|
|
NOTE Reception takes
Clock signal reception indicator:
STRONG SIGNAL | WEAK SIGNAL | NO SIGNAL |
|
|
|
MANUALLY SET CLOCK
1.Press and hold MODE to enter.
2.Press MODE to toggle between displays.
3. Press | or | to increase / decrease values of the |
selected setting. |
| |
4.Press MODE to confirm.
The settings order is: time zone offset, 12/24 hr format, hour, minute, year,
RM383PA: Select the time zone: (P) Pacific, (E) Eastern, (C) Central or (M) Mountain.
NOTE The language options are English (E), German (D), French (F), Italian (I), and Spanish (S).
To select display mode:
Press MODE to choose between clock with seconds and clock with weekday.
ALARM
To set the alarm:
1.Press ((.)) to toggle between Alarm 1 / 2.
2.Press and hold ((.)) to enter alarm setting.
3.Press 
/ 
to set hour / minute.
4.Press ((.)) to confirm or MODE to confirm and exit.
indicates alarm is ON.
To activate / deactivate alarm 1 and / or 2:
•Press 
.
To silence the alarm:
•Press SNOOZE to silence it for 8 minutes
OR
•Press any other button to turn the alarm off and activate it again after 24 hours.
PROJECTION
To activate / deactivate continuous projection:
•Slide PROJECTION switch when adaptor is connected.
To flip image by 180°:
•While image is projected, press SNOOZE.
To focus image:
•Turn FOCUS wheel.
NOTE If projection is illuminated, do not look directly into the projector.
RESET
Press RESET to return to the default settings.
PRECAUTIONS
•Do not subject the unit to excessive force, shock, dust, temperature or humidity
•Do not cover the ventilation holes with any items such as newspapers, curtains etc.
•Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft,
•Do not clean the unit with abrasive or corrosive materials.
•Do not tamper with the unit’s internal components. This invalidates the warranty.
•Only use fresh batteries. Do not mix new and old batteries.
•Images shown in this manual may differ from the actual display.
•When disposing of this product, ensure it is collected separately for special treatment.
•Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible. Consult the furniture manufacturer's care instructions for information.
•The contents of this manual may not be reproduced without the permission of the manufacturer.
•Do not dispose old batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.
•Please note that some units are equipped with a battery safety strip. Remove the strip from the battery compartment before first use.
NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice.
SPECIFICATIONS
TYPE | DESCRIPTION | |
L x W x H | 85 x 60 x 87 mm | |
(3.35 x 2.36 x 3.43 in) | ||
| ||
Weight | 170 g (6 oz) without battery | |
Power | AC/DC 3V adaptor | |
| 2 x |
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products. If you’re in the US and would like to contact our Customer Care department directly, please visit: www2.oregonscientific.com/service/support
OR
Call
For international inquiries, please visit: www2.oregonscientific.com/about/international
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www.oregonscientific.com), or on the warranty card for this product) for all inquiries instead.
We |
|
Name: | Oregon Scientific, Inc. |
Address: | 19861 SW 95th Ave.,Tualatin, |
| Oregon 97062 USA |
Telephone No.: | |
declare that the product | |
Product No.: | RM383PA |
Product Name: | Atomic Projection Clock with Ambient |
| Lighting |
Manufacturer: | IDT Technology Limited |
Address: | Block C, 9/F, Kaiser Estate, |
| Phase 1, 41 Man Yue St., Hung Hom, |
| Kowloon, Hong Kong |
is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
Horloge de projection atomique à
éclairage ambiant Modèle: RM383PA
MANUEL DE L’UTILISATEUR
FR
VUE D’ENSEMBLE
FACE AVANT (FIG 1)
1.LED de projection / Mise au point: permet d’ajuster l’image projetée
2.Horloge avec affichage des secondes / jours de la semaine
3.Calendrier
4.SNOOZE (Rappel d’alarme) : appuyez pour activer la fonction snooze / active le
5.Indicateur de réception du signal
6.Fuseau horaire
7.Mode d’affichage de l’alarme
8.Alarme 1/2 activée
*une fois l’adaptateur connecté, le
VUE DU BAS (FIG 2)
1.Compartiment des piles
2.PROJECTION ON / OFF : Active / désactive la projection continue
3./ : Augmente / diminue les valeurs du réglage sélectionné ; active / désactive le signal de réception de l’horloge.
4.((.)) ALARM : Visualisation du statut de l’alarme ; réglage de l’alarme.
5.ALARM ON / OFF: permet d’activer / désactiver l’alarme
6.MODE : modifie les réglages / l’affichage
7.Prise adaptateur CA / CC
8.RESET (REINITIALISER) : Réinitialise l’appareil aux réglages par défaut
POUR COMMENCER
INSTALLATION DE PILES
1.Retirer le compartiment à piles.
2.Installer les piles, en faisant correspondre les polarités (+ /
3.Appuyer sur RESET après chaque changement de piles.
HORLOGE
RÉCEPTION DE L’HORLOGE
Cet appareil est conçu pour synchroniser son horloge automatiquement avec un signal horaire.
RM383PA:
•Signal
Activer / désactiver la réception du signal :
Maintenez le bouton | pour activer, ou le bouton | pour |
désactiver la réception du signal. |
| |
REMARQUE La réception prend
Indicateur de réception du signal de l’Horloge :
SIGNAL FORT | SIGNAL FAIBLE | AUCUN SIGNAL |
|
|
|
REGLER MANUELLEMENT L’HORLOGE
1.Appuyez et maintenez la touche MODE pour entrer dans les réglages.
2.Appuyez sur MODE pour alterner entre :
3.Appuyez sur 
ou 
pour augmenter / diminuer les valeurs le réglage sélectionné.
4.Appuyez sur MODE pour confirmer.
Les réglages s’effectuent dans l’ordre suivant : Fuseau horaire, format 12/24 heures, heure, minutes, année, format
RM383PA: Sélectionne la zone horaire: (P) Pacific, (E) Eastern, (C) Central ou (M) Mountain.
REMARQUE Les options de langue sont Anglais (E), Alemand (D), Français (F), Italien (I), et Espagnol (S).
Pour sélectionner le mode d’affichage :
Appuyez sur MODE pour choisir entre l’horloge indiquant les secondes et celle indiquant les jours de la semaine.
RM38PA_M_USA_R2.indd 1
9/7/07 5:26:38 PM
