Oregon Scientific RRA320P specifications Overview Front View FIG, Back View FIG, TOP View FIG

LED Clock with Projection &

Analogue AM/FM Radio

Model: RRA320P

USER MANUAL

EN

OVERVIEW

FRONT VIEW (FIG. 1)

1			3
			4
2	5
		6

1.AM / PM

2.Clock

3.Radio ON

4.Sleep mode ON

5.Alarm 1 / 2 ON

6.Low Battery indicator

BACK VIEW (FIG. 2)

１

２

3

4

5

6

7

8 9 10 11

1.FOCUS Wheel: Adjust Projection Focus

2.RADIO: Turn radio On / Off, Select AM / FM

3.ALARM 1 and 2: Select alarm type, BEEP / OFF /

RADIO

4.+ / - : Increase / decrease values of the selected setting

5. / SET / , : Change settings / display / View respective alarm status; set alarm

6.DIMMER: Select display brightness LO / HI

7.PROJECTION ON: Enable / disable continuous projection

8.180° ROTATION: flip image180°

9.RESET: Reset unit to default settings

10.AC / DC Socket

11.Battery compartment

TOP VIEW (FIG. 3)

1

2

3

1.VOL: Mute / adjust radio volume

2.SNOOZE / SLEEP: silence alarm for 8 minutes

3.TUNE: Select radio frequency

GETTING STARTED

INSERT BATTERIES

1.Plug AC / DC adaptor into socket.

Memory backup:

2.Remove the battery compartment cover.

3.Insert the batteries, matching the polarities (FIG. 2).

SET CLOCK

1. Press .

2.Press + or - to change the settings.

3.The settings order is: 12/24 hr format, hour, minute.

RRA320P USA MANUAL R1.indd 1

ALARM

To set the alarm:

1. Press and hold desired SET / .

2.Press + / - to set hour / minute.

3. Press (or 10 seconds of inaction) to return display to clock mode.

To activate / deactivate alarm:

Slide to:

•OFF – disable alarm

•BEEP - beep alarm

•RADIO – Radio alarm

To silence the alarm:

•Press SNOOZE / SLEEP to silence it for 8 minutes

OR

• Press , SET / , + / - to turn the

alarm off and activate it again after 24 hours.

RADIO

To activate / deactivate radio:

1.Slide RADIO ON/OFF to turn on the radio.

2.Slide AM / FM to select.

3.Turn TUNE rotary dial to select frequency

To adjust volume:

• Turn VOL rotary dial to mute / adjust volume.

To activate sleep timer:

• Press SNOOZE / SLEEP to enter sleep mode.

• Press SNOOZE / SLEEP to change the sleep time. setting (120, 90, 60, 30, 15, 0 min).

PROJECTION

This unit projects time information for your convenience.

For continuous projection:

•Slide PROJECTION switch when adaptor is connected, to enable / disable.

To flip projected image by 180°:

•Press 180° Flip.

To focus image:

•Turn FOCUS wheel.

NOTE If projection is illuminated, do not look directly into the projector.

RESET

Press RESET to return to the default settings.

PRECAUTIONS

•Do not subject the unit to excessive force, shock, dust, temperature or humidity.

•Do not cover the ventilation holes with any items such as newspapers, curtains etc.

•Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft, lint-free cloth.

•Do not clean the unit with abrasive or corrosive materials.

•Do not tamper with the unit ’s internal components. This invalidates the warranty.

•Only use fresh batteries. Do not mix new and old batteries.

•Images shown in this manual may differ from the actual display.

•When disposing of this product, ensure it is collected separately for special treatment.

•Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible. Consult the furniture manufacturer’s care instructions for information.

•The contents of this manual may not be reproduced without the permission of the manufacturer.

•Do not dispose old batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

•Please note that some units are equipped with a battery safety strip. Remove the strip from the battery compartment before first use.

NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice.

SPECIFICATIONS

TYPE	DESCRIPTION
MAIN UNIT
L x W x H	183 x 67 x 81mm
	(72 x 26.4 x 31.9in)

Weight	386 g (13.6 oz)
	without battery
Power	6 V AC adaptor
	2 x UM-4 (AAA)
	1.5 V batteries

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products.

If you’re in the US and would like to contact our Customer Care department directly, please visit: www2.oregonscientific.com/service/support.asp

OR

Call 1-800-853-8883.

For international inquiries, please visit: www2.oregonscientific.com/about/international.asp.

EU-DECLARATION OF CONFORMITY

Hereby, Oregon Scientific, declares that this LED Clock with Projection & Analogue AM/FM Radio (Model: RRA320P) is in

compliance with EMC directive 89/336/CE.

A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio / TV technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www.oregonscientific.com), or on the warranty card for this product) for all inquiries instead.

We
Name:	Oregon Scientific, Inc.
Address:	19861 SW 95th Ave.,Tualatin,
	Oregon 97062 USA
Telephone No.:	1-800-853-8883
declare that the product
Product No.:	RRA320P
Product Name:	LED Clock with Projection &
	Analogue AM/FM Radio
Manufacturer:	IDT Technology Limited
Address:	Block C, 9/F, Kaiser Estate,
	Phase 1,41 Man Yue St., Hung

Hom, Kowloon, Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.

Horloge de projection LED avec

Radio AM / FM analogique

Modèle : RRA320P

MANUEL DE L’UTILISATEUR

FR

VUE D’ENSEMBLE

FACE AVANT (FIG.1)

1			3
			4
2	5
		6

1.AM / PM

2.Horloge

3.Radio activée

4.Mode sleep activé

5.Alarme 1/2 activée

6.Indicateur de faiblesse des piles

FACE ARRIERE ( FIG. 2)

１

２

3

4

5

6

7

8 9 10 11

1.Molette FOCUS : ajuste la mise au point de la projection

2.RADIO: active / désactive la radio, sélectionne la bande AM/FM

3.ALARME 1 et 2 : sélectionne le type d’alarme, par BIP, RADIO ou désactivée

4.+ / - :Augmente / diminue les valeurs du réglage sélectionné

5.	/ SET	,	: modifie les réglages /
	l’affichage / le statut de l’alarme ; règle l’alarme

6.DIMMER : ajuste la clarté de l’affichage HI / LO

7.PROJECTION ON : active / désactive la projection continue

8.180° ROTATION : permet de renverser l’image à 180°

9.RESET (REINITIALISER) : réinitialise l’appareil aux réglages par défaut

10.Prise adaptateur

11.Compartiment des piles

VUE DU HAUT (FIG. 3)

1

2

3

1.VOL : muet / ajuste le volume de la radio

2.SNOOZE / SLEEP : éteint l’alarme pour 8 minutes

3.TUNE : sélectionne la fréquence radio

POUR COMMENCER

MISE EN PLACE DES PILES

1.Branchez l’adaptateur dans la prise.

Protection de la mémoire :

2.Retirez le couvercle du compartiment des piles.

3.Insérez les piles, en respectant les polarités (voir FIG. 2).

RÉGLER L’HORLOGE

1.Appuyez sur .

2.Appuyez sur + ou – pour modifier les réglages.

3.Les réglages s’effectuent dans l’ordre suivant : Format 12/24 h, heure, minute.

ALARME

Pour régler l’alarme :

1. Maintenez appuyé SET ou .

2.Appuyez sur + / - pour régler l’heure / les minutes.

3. Appuyez sur (ou ne rien faire pendant 10 secondes) pour revenir à l’affichage du mode horloge.

Pour activer/ désactiver l’alarme :

Placez l’encoche sur :

•OFF – pour désactiver l’alarme

•BEEP – pour l’alarme par bip

•RADIO – pour l’alarme par radio

Pour couper le son de l’alarme :

•Appuyez sur SNOOZE / SLEEP, pour éteindre l’alarme pendant 8 minutes

OU
• Appuyez sur	, SET	/	, + / -, pour

éteindre l’alarme et pour qu’elle se déclenche 24 heures plus tard.

RADIO

Pour activer/ désactiver la radio :

1.Positionnez l’encoche RADIO sur ON pour activer la radio.

2.Positionnez l’encoche sur AM / FM pour sélectionner la bande désirée.

3.Tournez la molette TUNE pour sélectionner la fréquence.

Pour ajuster le volume :

•Tournez la molette VOL pour mettre le volume sur muet ou pour l'ajuster.

Pour activer le compteur sleep :

•Appuyez sur SNOOZE / SLEEP pour entrer dans le mode sleep.

•Appuyez sur SNOOZE / SLEEP pour modifier le réglage du temps sleep (120, 90, 60, 45, 30, 15, 0 minutes).

PROJECTION

Cet appareil projette l’heure pour votre commodité.

Projection continue :

•Positionnez l’encoche PROJECTION sur ON une fois l’adaptateur branché, pour activer / désactiver la projection continue.

Renverser l’image projetée par 180° :

•Appuyez sur 180° Flip.

Mettre au point l’image :

•Tournez la molette FOCUS.

REMARQUE Si la projection est activée, ne regardez pas directement dans le projecteur.

REINITIALISATION

Appuyer sur RESET pour revenir aux réglages par défaut.

PRECAUTIONS

•Ne pas soumettre le produit à une force excessive, au choc, à la poussière, aux changements de température ou à l’humidité.

•Ne pas couvrir les trous de ventilation avec des journaux, rideaux etc…

•Ne pas immerger le produit dans l’eau. Si vous renversez du liquide sur l’appareil, séchez-le immédiatement avec un tissu doux.

•Ne pas nettoyer l’appareil avec des matériaux corrosifs ou abrasifs.

•Ne pas trafiquer les composants internes. Cela invalidera votre garantie.

•N’utilisez que des piles neuves. Ne pas mélanger des piles neuves et usagées.

8/29/07 10:16:57 AM