Oricom M5050 Make an intercom call, Transfer a call between handsets, Switch between calls

ABOUT YOUR PHONE

6 Multi-handset use

Your M5000 series phone can have up to 5 handsets registered to 1 base unit. Each handset has its own number HS-1, HS-2, HS-3, HS-4, & HS-5 shown on the left-hand side of the display.

Notes

•A maximum of 1x outside call & 2x intercom calls can take place per base unit.

•If you make an outside call + another handset is on line = result is a busy tone.

•If you make an intercom call + one is already in progress = result is a busy tone.

With 2 or more handsets you can:

Make an intercom call

1.Press INTERCOM button. When you hear your outgoing message, press

2.Key the handset number 1, 2, 3, 4, OR 5, you wish to call.

3.On the RECIEVING handset, press PHONE button.

4.To end, press PHONE button on the CALLING handset. The RECIEVING handset will hear a busy tone.

Transfer a call between handsets

1.Press INTERCOM button.

2.Key the handset number 1, 2, 3, 4, OR 5, you wish to call.

3.On the RECIEVING handset, press PHONE button to receive call.

4.Press PHONE button on the CALLING handset to transfer. Call will return back within 90 seconds if unanswered.

Switch between calls

An outside call + an intercom call in progress, you switch between the 2 calls:

1.Press INTERCOM button to speak to outside call, while the intercom call is on hold.

2.Press INTERCOM button again to speak to intercom call, while outside call is on hold.

3.Press PHONE to transfer outside call to the other handset (while connected to intercom call).

Note

•If you press the PHONE button while connected to the outside call, you will disconnect

•If the other handset user presses the PHONE button to hang up, you will be left with the outside call

Conference calls

A 3-way call between yourself + outside call + intercom call:

1.Either make or answer an outside call.

2.Press INTERCOM button.

3 Key in the other handset number 1, 2, 3, 4, OR 5.

4.On the RECIEVING handset, press PHONE button to receive call.

5.Press INTERCOM button & hold for about 3 seconds.

5. When connected both symbols are shown on display

M5050 User guide.doc Page 5 of 6

ABOUT YOUR PHONE

7 Notes for operation in New Zealand

The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with the minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services. This device may be subject to ringing or bell tinkle when certain other devices are connected to the same line. If this occurs, the problem should not be referred to the Telecom Faults service.

This equipment shall not be set to make automatic calls to the Telecom “111” Emergency Service. This equipment may not provide for the effective hand-over of a call to another device connected to the same line.

REN (RN for New Zealand)

The REN (Ringer Equivalence Number) or (RN) is of significance only if you wish to connect more than 1 telephone to your telephone line. A standard telephone line has a maximum REN capacity of 3 (RN of 5). It is possible to connect 3(5) devices with a REN of 1 (RN of 1) with no degradation to the product’s performance. Exceeding this limit may cause the volume of the ringer in any phone to decrease or not ring at all.

Caller ID

Customers in NZ using NON-TELECOM toll services should not use the ‘dial back’ feature for local calls as this will incur a charge only the 7 digit number should be dialled. Some of the CID services listed may not be available in New Zealand. This telephone is NOT designed for making emergency telephone calls when the power fails. Ensure there are alternative arrangements for access to emergency services via a mobile phone or a corded telephone.

8 Warranty Information

This product is covered by a 12 month warranty against defective workmanship or parts. The warranty does not extend to damage caused by misuse, negligence, excessive voltage, faults on the telephone line or lightning. This guarantee in no way affects your statutory rights. Full details of the warranty are contained in the enclosed warranty card. If you feel this product is not working correctly please consult the user guide and ensure that you are using the product in accordance with the instructions. Remove all extra telephone equipment and connect only this telephone directly to the telephone socket.

If the fault is still present, connect another telephone (if available) to the telephone socket. The results will show you whether the fault lies with this unit or with the telephone line. If the product is working correctly the fault is on the telephone line. Please contact your network operator for assistance

To orders spare parts additional handsets, replacement batteries and in case of any technical issues you may have with product please consult our website for further information or send us an email for a prompt response to your enquiry. In the unlikely event of a fault developing, please contact us for assistance. If the product is then found to be faulty you will be asked to return it directly to us with a copy of the purchase receipt.

Australia	New Zealand
Oricom International Pty Ltd	Atlas Gentech (NZ) Ltd
PO Box 5681, South Windsor, NSW 2756	Private Bag 14927, Panmure, Auckland
Customer support	Customer support
Email: support@oricom.com.au	Email: support@atlasgentech.co.nz
Web: www.oricom.com.au	Web: www.atlasgentech.co.nz
Fax: (02) 4572 0939	Fax: (09) 574 2722
Ph: 1300 889 785	Ph: 0900 50 025 (Toll Call)
	M5050 User guide.doc Page 6 of 6