Heavy-Duty Detachable
IMPORTANT SAFEGUARDS
Commercial Clipper • When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using this appliance.
GETTING FAMILIAR WITH
YOUR CLIPPER
Due to continuous product improvement, product may vary slightly from
AVAILABLE OSTER® LUBRICANTS & CLEANERS,
& REPLACEMENT PARTS
Regular use of the following products will help you enjoy optimum performance from your
USING YOUR CLIPPER
Important:
• Before using your clipper, apply 1 or 2 drops of Oster® Clipper & Blade |
Blade Clipper
Instruction Manual
• For Commercial Use Only •
Model 10 - 76010
DANGER
To reduce the risk of electric shock:
1.Do not reach for an appliance that has fallen into water. Unplug immediately.
2.Do not use while bathing or in a shower.
3.Do not place or store appliance where it can fall or be pulled into a tub or sink.
4.Do not place in or drop into water or other liquid.
5.Always unplug this appliance from the electrical outlet immediately after using.
6.Unplug this appliance before cleaning, putting on or taking off parts.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1.An appliance should never be left unattended when it is plugged in.
2.Close supervision is necessary when this appliance is used by, on, or near children or invalids.
3.Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
5.Keep cord away from heated surfaces.
6.Never operate the appliance when air openings are blocked or while on a soft surface (such as a bed or couch).
7.Never drop or insert any object into opening.
8.Do not use outdoors or operate where aerosol spray products are being used or where oxygen is being administered.
9.Do not use this appliance with a damaged or broken comb or blade, as cut or scratched skin may occur.
10.To disconnect, move all controls to “OFF”, then remove plug from outlet.
11.Do not wrap cord around unit when storing. Continuous stress on the cord can damage cord insulation and result in a shock hazard.
12.Avoid contact with moving blades.
13.Avoid tangling or kinking the cord while clipping. Should the cord become tangled or kinked, stop clipping and straighten the cord.
what is illustrated.
1.Blade guard
2.Blade
3.Blade bracket
4.Blade hinge
5.Name plate/gear drive assembly access
6.Carbon brush cap/carbon brush
7.Oiler
8.Power cord
9.On/Off switch
10.Hanging ring
11.Cleaning Brush
12.Oster® Clipper & Blade Lube™ oil
13.Oster Gear Lube® grease
1
11
2
3/4
5
4 | 12 |
7
clipper and prolong its functionality.
Oster | Kool Lube® 3 | Spray | Blade Wash® |
Disinfectant | Cleaning | ||
Lubricates and |
| Solution 76300- | |
& blade lubricant | cools down blade. | Minimizes bacteria | 103 |
and disinfectant. |
| ||
| buildup between | Flushes away | |
|
| upper and lower | |
|
| accumulated hair | |
|
| blades. | |
|
| and removes dirt | |
|
|
| |
|
|
| buildup trapped |
|
|
| between upper |
|
|
| and lower cutting |
|
|
| blades. |
|
|
|
|
| Lube™ Oil to the blade (refer to Taking Care of Your Clipper section). |
• | For best results, hair should be clean and free from styling agents. |
• | During use, apply Kool Lube® coolant occasionally to the blades to keep |
| them cool. |
1.Plug unit into an AC electrical outlet.
2.Move On/Off switch to turn clipper on.
3.Remove blade guard.
4.Insert blade. Holding blade sides, slide blade bracket into hinge.
5.Push blade toward the clipper until it snaps into place
STEP 4
STEP 5
6.When finished clipping, turn clipper off and unplug cord from electrical outlet.
7.Cover blade with blade guard to keep it protected.
TAKING CARE OF YOUR CLIPPER
Note: Any other maintenance not explained in this manual must be per- formed by an
Important: Make sure clipper is turned off and unplugged from electrical
SAVE THESE INSTRUCTIONS
THE FOLLOWING PARAGRAPH IS FOR 120-VOLT MARKETS ONLY
To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way. This is a safety feature intended to help reduce the risk of electrical shock. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
ABOUT YOUR CLIPPER
Although your clipper has been thoroughly tested and inspected at every stage of its manufacturing and assembly, it is recommended that you lubri- cate it, as instructed in this manual, after
6
66
13
10 | 9 | 8 |
Blade Lube™ | Gear Lube® | Replacement carbon brushes | |
Oil |
|
| |
Lubricates between | Specially designed | Set of replacement carbon brushes and | |
upper and lower | to prolong the life of | ||
springs | |||
blades to keep | gears, bearings and | ||
| |||
them sharper lon- | the motor. |
| |
ger and produce a |
|
| |
smoother clipping |
|
| |
action |
|
|
To order any of these products, please call
outlet before removing, replacing or cleaning any parts. Lubricating Motor
If you hear a “squeal” or a dry bearing noise from the motor, it is a signal that the motor needs lubricating.
Remove cap from Oster® Clipper and Blade | APPLY 1 |
Lube™ tube and insert tip into oiler to apply 1 | |
drop of oil. Be careful not to over lubricate. | DROP |
Greasing Gear Drive Assembly
We recommend checking the gear drive assembly every six months for greasing.
Caution: Grease only when necessary as
8/7/12 11:03 AM
