Owner’s Manual
Amplifier Operation
Power Control Connections
Your Outlaw amplifier features a
Remote
Equipped With a 12 Volt Trigger Jack
Press the front panel power switch on the amplifier so that it is in the ON posi- tion. Then, using an accessory cable with a 3.5mm mono
Remote Turn on Using External AC to DC
Power Converter
If your processor or receiver does not have a dedicated trigger jack, it is still possible to activate the unit for automatic turn on when a Switched Outlet is available on the rear of the source device. To control the amplifier in this fashion you will need a small AC to DC power converter, capable of delivering a 6 to 12 volt DC signal. The DC voltage should terminate in a standard 3.5mm type mini plug. This type of converter may be obtained as a Power Adapter from many electronics retailers.
When installing, press the Main Power Switch on the front panel of the amplifier in so that it is in the ON position. Plug the AC adapter into a switched outlet that will be activated when you wish to have the amplifier turn on. This may be the switched outlet at the rear of an AC receiver or other audio equipment. Connect the 3.5mm
Power Connection
Once all audio and system connections have been made, connect the supplied power cord to the amplifier first, and then connect it to an AC power source. Please make certain that the amplifier is turned off and that the device con- nected to the remote trigger input is off when connecting the power cord and plugging it into an AC outlet.
CAUTION: Do not plug the amplifier directly into the “Switched Acces- sory” outlet of another device! These outlets are intended for use with low current draw products having a low current draw, such as tuners, CD players or cassette decks. These cannot handle the high current draw of a power amplifier. Using these outlets for a power amplifier is a significant safety hazard.
NOTE: It is not recommended that you connect other power amplifiers or products with a high current draw, to the same AC power circuit as the amplifier, unless they are used with the remote power turn on and sequenc- ing system. The simultaneous
Amplifier Operation
After all connections have been made you are ready for listening. First, turn on the source components and processor in your system. It is always a good idea to turn on your amplifier LAST. This avoids the possibility of any turn on pops or transients from other equipment being amplified and sent to your speakers where they may cause damage. Always start with a low volume level on your controller or preamp to avoid damage to your speakers.
Manual On
Simply press the front panel Power/Standby button until the light is illuminated. There will be a short pause from the time the power is turned on until power is applied to the speakers. This is intentional, and protects your speakers from damage while the amplifier stabilizes. You may also hear a relay click during start up. This is also normal.
To turn the unit off, press the Power/Standby button again. The indicator light will go out.
Automatic On
Make certain that the connection to the processor, or other controlling device is correct, as described on page ?. Whenever the controlling device is turned on, the amplifier will automatically turn on after a short pause. This pause is inten- tional, and it protects your speakers from damage while the amplifier stabilizes. You may also hear a relay click as during start up. This is also normal.
To turn off your amplifier, simply turn off the unit that feeds the amplifier it’s audio signals. The amplifier will automatically go into a stand by mode in a few moments.
Output Settings
All volume and level adjustments are made at your preamp, controller or sur- round processor. To assure proper sound field imaging, it is always a good idea to
Care and Maintenance
Cleaning
When the unit becomes dirty, wipe it with a clean, soft, dry cloth. If necessary, first wipe the surface with a soft cloth slightly dampened with mild soapy water, then with a fresh cloth dampened with clean water. Wipe dry immediately with a dry cloth. NEVER use benzene, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of the metal parts. Avoid spraying insecticide, waxes, polishing agents, or any aerosol product near the unit.
When You Are Away
If you will not be using your home theater system for an extended period of time, it is always a good idea to turn the unit off using the Power Switch on the rear panel of the amplifier. This will prevent the automatic turn on circuits from accidentally turning the system on during your absence.
8
Outlaw Audio
