Panasonic AJ-HD1700 SYS H HD Coarse, Sys Sc Sd, VO SYS H SD Coarse, SD SYS D SD Coarse, Cap.Lock

Setup menus

<Menu management accompanying switching the system frequency>

The system menu and setup menu have some items whose settings differ and other items with which no selection options are displayed and whose settings are fixed (indicated by the shading in the table below), depending on the switching of the operation mode in response to the setting selected for system menu item No.25 (SYSTEM FREQ). (Refer to the table below.)

System menu and setup menu settings

• Each of the items whose settings differ is saved in the VTR MEMORY (current file and one of the backup files 1 to 4). The settings that correspond to each operation mode will be displayed so that the settings can be performed for each operation mode.

Registration of the <PF1> and <PF2> function buttons

•When the items whose settings differ have been registered in the <PF1> and <PF2> function buttons, the settings that correspond to each operation mode

will be displayed so that the settings can be performed for each operation mode.

•If items, whose selection options are not displayed due

to the operation mode, have been registered in the
<PF1> or <PF2> function button, when an operation
mode in which these options are not displayed is
selected, what has been registered is saved but the
function button itself will become blank and cannot be
operated. Bear in mind, however, that when the data is
registered again, it is saved by overwriting the existing
data so that the previously registered data will be lost	.

<50P IN/OUT> 50-pin connector registration

•When the items whose settings differ have been registered in the <50P IN/OUT> 50-pin connector pins, the settings corresponding to the operation modes are allocated to the IN and OUT pins on the basis of the setting numbers. However, when the

upper limit value is exceeded, the value will be limited to this upper limit.

What has been registered is saved, but bear in mind that when the data is registered again, it is saved by overwriting the existing data so that the previously registered data will be lost.

•If items, whose selection options are not displayed

due to the operation mode, have been registered in

the <50P IN/OUT> 50-pin connector, when an operation mode in which these options are not displayed is selected, what has been registered is

saved but no operation is possible. Bear in mind, however, that when the data is registered again, it is saved by overwriting the existing data so that the previously registered data will be lost.

System menu

No.

Menu item

System menu No.25 (SYSTEM FREQ)

59/60

23/24

50

25 (HD)

25 (SD)

12

SYS H (HD)

COARSE

j5H to 0H to 5H

j5H to 0H to 5H

j5H to 0H to 5H

FINE

j1100 to 0 to 1100

j1375 to 0 to 1375

j1320 to 0 to 1320

14

SYS SC (SD)

j108 to 0 to 108

j115 to 0 to 115

15

VO SYS H (SD)

COARSE

j5H to 0H to 5H

j5H to 0H to 5H

FINE

j858 to 0 to 858

j864 to 0 to 864

16

SD SYS D (SD)

COARSE

j5H to 0H to 5H

j5H to 0H to 5H

FINE

j858 to 0 to 858

j864 to 0 to 864

Setup menus

No.

Menu item

System menu No.25 (SYSTEM FREQ)

59/60

23/24

50

25 (HD)

25 (SD)

109

CAP.LOCK

2F /4F

2F

2F/4F/8F

2F

2F

501

VITC POS-1

10L to 16L

to 20L

7L to 11L

to 22L

7L to 11L

to 22L

502

VITC POS-2

10L to 18L

to 20L

7L to 13L

to 22L

7L to 13L

to 22L

INTSG

INTSG

HDSDI

600

VIDEO IN SEL

HDSDI

SDTI

SDSDI

SDSDI

The underlining (__) denotes the factory setting mode.

(Continued on next page)

106