Panasonic CF-19CDBAXVM 9.2. Reassembly Instructions

9-9

9.2. Reassembly Instructions

9.2.1. Attention when CF-19 series is repaired

• Please execute writing BIOS ID when you exchange the Main Board.

• Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.

9.2.2. Setting up the Inverter Ass'y and LCD UNIT

1. Set the LCD UNIT to the LCD Front Cabinet/TS Panel.

2. Set the TS PCB on the LCD Back Damper, and connect

the 2 Cables to the Connectors (CN900 and CN901).

3. Set the Inverter PCB to the LCD Back Damper, and con-

nect the 2 Cables to the Connectors.

n Assembly of LCD Back Damper (Applicable Model : Touch Screen Model)

Inverter Case

Tape

Inverter PCB

Connector

Connector

LCD Unit

TS PCB

Connector

(CN901)

Connector (CN900)

LCD PWB SPACER ASSY

Asymmetric Shape

A

Remove the Release Paper on

the back side and attach it.

Crosswise: Match to the middle line.

LCD PWB SPACER ASSY

Insert this between

LCD PCB & LCD Frame.

Match both Holder Sheet and LCD

Back Cushion Side to the right

edge of the Frame. (0 to 0.5 mm)

0 0.5mm

00.5mm

0 0.5mm

0 3mm

Detail of "A"

BCD

0 1mm

0 0.5mm

0 1mm

1 1.5mm

0 1mm

0 0.5mm

Detail of "D"

Attach to the side surface if the Frame.

(Match to the end of the Frame within

0 to 0.5 mm at the far side.)

0.5mm

00.5mm

0.5mm

0.5mm

0.5mm

0.5mm

After setting LCD

Back Damper,

fix them together.

Note: Apply the load to attach. 20 to 30N (2.0 to 3.0 Kgf)

Order of fixingLCD Side Cushion ASpacer Sheet Spacer SheetLCD PCB Spacer

Screw the Board and

the Spacer together.

Screw

Detail of "B" Detail of "C"

Screw the Board and

the Spacer together.

LCD Side Cushion CLCD Side Cushion DHolder SheetLCD Back Cushion SideLCD Back DamperHolder SheetLCD Back Cushion Side

Lengthwise: Match to the LCD Frame.

Cover the hook of

the Frame. (0 to 0.5 mm)

Cover the hook of

the Frame. (0 to 0.5 mm)

Pass the Cable

under the protrusion.

Pass the Cable

under the protrusion.

Pass the Cable

through the space.

LCD Side Cushion C

Screw

Screw

LCD Side Cushion S

After setting LCD

Back Damper,

fix them together.

Screw

LCD Back Cushion L LCD Back Cushion S

Match both Holder Sheet and LCD

Back Cushion Side to the right

edge of the Frame. (0 to 0.5 mm)

Contents

Main Page Page Page CONTENTS MainSpecifications 1 Specifications Wireless LAN <Only for model with wireless LAN> BluetoothTM <Only for model with Bluetooth> 1-2 MB 2 Names and Functions of Parts Page 3 Block Diagram PC2-3200 3-1 XGA SO-DIMM Extension Memory Page 4.2. Troubleshooting 5 Power-On Self Test (Boot Check) Outline of POST 5-1 Error Diagnosis by Checking Beep Signal Sound 6 List of Error Codes Page 7 Self Diagnosis Test 1-1. Setting of content of setup 1. Beginning of self-diagnosis test 1-2. When you execute an automatic test 1-3. When you execute the enhancing test 2. Operation of PC-Diagnostic Utility 2-3. The content of the setup is returned to the setting of the user 2-1. Selection of tested device 2-2. "PC-Diagnostic utility" End method 7.1. Test Item and Division of trouble Page 8 Wiring Connection Diagram 9 Disassembly/Reassembly 9.1. Disassembly Instructions 9.1.1. Preparation 9.1.2. Removing the Battery Pack and HDD Pack 9.1.3. Removing the Touch Pad and Key- board 9.1.4. Removing the DIMM Lid Assy 9.1.5. Removing the Rear Cabinet 9.1.6. Removing the DU Lid Unit 9.1.7. Removing the HSDPA PCB and Bluetooth PCB 9.1.8. Removing the Audio PCB 9.1.9. Removing the Main PCB, Wireless Module, SD PCB, Antenna PCB and Modem PCB 9.1.10. Removing the I/O PCB Ass'y 9.1.11. Removing the Power SW PCB 9.1.12. Removing the left LED and right LED PCB 9.1.13. Removing Pad PCB and SW PCB 9.1.14. Removing the Display unit 9.1.15. Removing the LCD Rear Case 9.1.16. Removing the LCD Hinge 9.1.17. Removing Inverter PCB and LCD Unit 9.1.19. Removing the Each Cover 9-9 9.2. Reassembly Instructions LCD Side Cushion C LCD Side Cushion D LCD Side Cushion C 9-10 n Assembly of LCD Back Damper (Application Model : Digitizer Model) Inverter MIL Cover MIL Sheet n Assembly of Inverter PCB 9-11 n Assembly of Inverter PCB (Applicable Model : Touch Screen Model) 9-12 n Assembly of Inverter PCB (Application Model : Digitizer Model) n Assembly of Touch Screen (Applicable Model : Touch Screen Model) Page 9-14 n Line Processing of Antenna Cable 9.2.4. Setting up the LCD Hinge 9-15 n Assembly of LCD Hinge Lock Spring Cable Holder LCD Rear side 9.2.5. Assembling the Antenna Cover, the Tablet Latch Cover and the LCD Rear Case 9-17 n Assembly of LCD Rear Case (Applicable Model : Touch Screen Model) n Assembly of LCD Rear Case (Applicable Model : Digitizer Model) 9-18 n Assembly of Tablet Latch Cover and Antenna Cover 9.2.6. Setting the Display Unit 9-20 n Assembly of Display Unit A Screw Screw Screw Screw 9.2.7. Setting the Pad PCB and SW PCB 9-22 n Assembly of the Pad PCB and SW PCB Connector(CN806) n Putting of the TP Bottom Tape 9.2.8. Setting the left LED PCB and right LED PCB Release Paper Release Paper left LED PCB right LED PCB Connector(CN801) 9-23 n Assembly of the left LED PCB and right LED PCB 9.2.9. Setting the Power SW PCB <N1> Connector(CN9) Power SW PCB 9.2.10. Setting the I/O PCB Ass'y 9.2.11. Setting the Main PCB, Wireless Module, SD PCB, DU PCB, Antenna PCB and Modem PCB Page Page 9-27 n Assembly of Main PCB 9-28 9-29 n Assembly of Main Unit Main PCB Assy 9.2.12. Setting the Audio PCB 9.2.13. Setting the HSDPA PCB and Bluetooth PCB 9-32 n Line Processing of Antenna Cable of Main Unit 9.2.14. Assembling the DU Lid Unit 9-34 9.2.15. Setting the Rear Cabinet n Cautions for Setting the Rear Cabinet 9.2.16. Setting the DIMM Lid Ass'y 1. Fix the DIMM Lid Ass'y using the 4 Screws. <K14-8> Screws <K14-8> : DRHM5025YAT 9.2.17. Setting the Touch Pad and Keyboard 9-36 Putting of the Sheet Keyboard Plate(R) Keyboard Assy TP Tape 9-37 n Putting of the Palm Rest ASSY n Putting of the KBD Tape 9.2.18. Setting the Battery Pack and the HDD Pack 9-39 n Assembly of the HDD ASSY 9.2.19. Assembling the Each Cover 10 Exploded View Screwtighteningtorque 10-1 Screwtighteningtorque 0.2_0.02Nm (2.0_0.2kgfcm) 0.3_0.03Nm (3.0_0.3kgfcm) 10-2 B C E Screwtighteningtorque 0.2_0.02Nm (2.0_0.2kgfcm) 0.4_0.02Nm (4.0_0.2kgfcm) 10-3 A H ++ ++ Screwtighteningtorque 0.2_0.02Nm (2.0_0.2kgfcm) 10-4 A++ CF- 19C DB A XVM Screw tightening torque 10-5 D 0.2 _ 0.02N m (2.0 _ 0.2kgf cm) 0.8 _ 0.08N m (8.0 _ 0.8kgf cm) CF- 19C D B AXV M Screw tightening torque + 0.18 _ 0.02N m (1.8 _ 0.2kgf cm) + 10-6 Screw tightening torque B C D 10-7 Replacement Parts List CF-19CDBAXVM (2006/11/20) REF. NO andAREA Page Page Page Page Page Replacement Parts List CF-19CDBAXVM (2006/11/20) PART NO. DESCRIPTION Q'T Y MAIN PCB REF. NO and AREA Page Page Page Page Page AUDIO PCB IO PCB PAD PCB SW PCB LED-LEFT PCB PR PCB LED-RIGHT PCB SD PCB HSDPA PCB POWER SW PCB EXTENAL ANTENNA PCB BLUETOOTH PCB HDD FPC BATTERY FPC