Panasonic CF-19CDBAXVM - page 9

Left side

Rear side Bottom

A: DC-IN Jack

B: USB Port

Reference Manual “USB Devices”

C: IEEE 1394 Interface Connector

Reference Manual “IEEE 1394 Devices”

D: Modem Port

Reference Manual “Modem”

E: LAN Port

Reference Manual “LAN”

F: SD Memory Card Indicator

(Blinking: During access)

Reference Manual “SD Memory Card”

G: SD Memory Card Slot

Reference Manual “SD Memory Card”

H: Wireless Switch

Reference Manual “Wireless Switch Utility”

I: PC Card Slot

Reference Manual “PC Card / ExpressCard”

J: ExpressCard Slot

Reference Manual “PC Card / ExpressCard”

K: Headphone Jack

You can connect headphones or ampliÞ ed speakers.

When they are connected, audio from the internal

speakers is not heard.

L: Microphone Jack

A condenser microphone can be used. If other types

of microphones are used, audio input may not be pos-

sible, or malfunctions may occur as a result.

When recording in stereo using a stereo micro-

phone:

Double-click in the notiÞ cation area, click [Op-

tions] - [Properties], and add a check mark for [Re-

cording], click [OK] - [Options] - [Advanced Controls]

- [Advanced], remove a check mark for [Mono Micro-

phone], and then click [Close].

When using a monaural microphone with a 2-termi-

nal plug:

With the settings outlined above, only audio on the

left track will be recorded.

When monitoring the microphone audio using head-

phones, sounds on the left track cannot be heard,

regardless of the above settings. This is a result of the

computer’s speciÞ cations, and is not a malfunction.

M: Security Lock

A Kensington cable can be connected.

For further information, read the manual that comes

with the cable.

N: External Display Port

Reference Manual “External Display”

O: Serial Port

P: RAM Module Slot

Reference Manual “RAM Module”

Q: Expansion Bus Connector

Reference Manual “Port Replicator / Car Mounter”

R: External Antenna Connector

2-2

Contents

Main Page Page Page CONTENTS MainSpecifications 1 Specifications Wireless LAN <Only for model with wireless LAN> BluetoothTM <Only for model with Bluetooth> 1-2 MB 2 Names and Functions of Parts Page 3 Block Diagram PC2-3200 3-1 XGA SO-DIMM Extension Memory Page 4.2. Troubleshooting 5 Power-On Self Test (Boot Check) Outline of POST 5-1 Error Diagnosis by Checking Beep Signal Sound 6 List of Error Codes Page 7 Self Diagnosis Test 1-1. Setting of content of setup 1. Beginning of self-diagnosis test 1-2. When you execute an automatic test 1-3. When you execute the enhancing test 2. Operation of PC-Diagnostic Utility 2-3. The content of the setup is returned to the setting of the user 2-1. Selection of tested device 2-2. "PC-Diagnostic utility" End method 7.1. Test Item and Division of trouble Page 8 Wiring Connection Diagram 9 Disassembly/Reassembly 9.1. Disassembly Instructions 9.1.1. Preparation 9.1.2. Removing the Battery Pack and HDD Pack 9.1.3. Removing the Touch Pad and Key- board 9.1.4. Removing the DIMM Lid Assy 9.1.5. Removing the Rear Cabinet 9.1.6. Removing the DU Lid Unit 9.1.7. Removing the HSDPA PCB and Bluetooth PCB 9.1.8. Removing the Audio PCB 9.1.9. Removing the Main PCB, Wireless Module, SD PCB, Antenna PCB and Modem PCB 9.1.10. Removing the I/O PCB Ass'y 9.1.11. Removing the Power SW PCB 9.1.12. Removing the left LED and right LED PCB 9.1.13. Removing Pad PCB and SW PCB 9.1.14. Removing the Display unit 9.1.15. Removing the LCD Rear Case 9.1.16. Removing the LCD Hinge 9.1.17. Removing Inverter PCB and LCD Unit 9.1.19. Removing the Each Cover 9-9 9.2. Reassembly Instructions LCD Side Cushion C LCD Side Cushion D LCD Side Cushion C 9-10 n Assembly of LCD Back Damper (Application Model : Digitizer Model) Inverter MIL Cover MIL Sheet n Assembly of Inverter PCB 9-11 n Assembly of Inverter PCB (Applicable Model : Touch Screen Model) 9-12 n Assembly of Inverter PCB (Application Model : Digitizer Model) n Assembly of Touch Screen (Applicable Model : Touch Screen Model) Page 9-14 n Line Processing of Antenna Cable 9.2.4. Setting up the LCD Hinge 9-15 n Assembly of LCD Hinge Lock Spring Cable Holder LCD Rear side 9.2.5. Assembling the Antenna Cover, the Tablet Latch Cover and the LCD Rear Case 9-17 n Assembly of LCD Rear Case (Applicable Model : Touch Screen Model) n Assembly of LCD Rear Case (Applicable Model : Digitizer Model) 9-18 n Assembly of Tablet Latch Cover and Antenna Cover 9.2.6. Setting the Display Unit 9-20 n Assembly of Display Unit A Screw Screw Screw Screw 9.2.7. Setting the Pad PCB and SW PCB 9-22 n Assembly of the Pad PCB and SW PCB Connector(CN806) n Putting of the TP Bottom Tape 9.2.8. Setting the left LED PCB and right LED PCB Release Paper Release Paper left LED PCB right LED PCB Connector(CN801) 9-23 n Assembly of the left LED PCB and right LED PCB 9.2.9. Setting the Power SW PCB <N1> Connector(CN9) Power SW PCB 9.2.10. Setting the I/O PCB Ass'y 9.2.11. Setting the Main PCB, Wireless Module, SD PCB, DU PCB, Antenna PCB and Modem PCB Page Page 9-27 n Assembly of Main PCB 9-28 9-29 n Assembly of Main Unit Main PCB Assy 9.2.12. Setting the Audio PCB 9.2.13. Setting the HSDPA PCB and Bluetooth PCB 9-32 n Line Processing of Antenna Cable of Main Unit 9.2.14. Assembling the DU Lid Unit 9-34 9.2.15. Setting the Rear Cabinet n Cautions for Setting the Rear Cabinet 9.2.16. Setting the DIMM Lid Ass'y 1. Fix the DIMM Lid Ass'y using the 4 Screws. <K14-8> Screws <K14-8> : DRHM5025YAT 9.2.17. Setting the Touch Pad and Keyboard 9-36 Putting of the Sheet Keyboard Plate(R) Keyboard Assy TP Tape 9-37 n Putting of the Palm Rest ASSY n Putting of the KBD Tape 9.2.18. Setting the Battery Pack and the HDD Pack 9-39 n Assembly of the HDD ASSY 9.2.19. Assembling the Each Cover 10 Exploded View Screwtighteningtorque 10-1 Screwtighteningtorque 0.2_0.02Nm (2.0_0.2kgfcm) 0.3_0.03Nm (3.0_0.3kgfcm) 10-2 B C E Screwtighteningtorque 0.2_0.02Nm (2.0_0.2kgfcm) 0.4_0.02Nm (4.0_0.2kgfcm) 10-3 A H ++ ++ Screwtighteningtorque 0.2_0.02Nm (2.0_0.2kgfcm) 10-4 A++ CF- 19C DB A XVM Screw tightening torque 10-5 D 0.2 _ 0.02N m (2.0 _ 0.2kgf cm) 0.8 _ 0.08N m (8.0 _ 0.8kgf cm) CF- 19C D B AXV M Screw tightening torque + 0.18 _ 0.02N m (1.8 _ 0.2kgf cm) + 10-6 Screw tightening torque B C D 10-7 Replacement Parts List CF-19CDBAXVM (2006/11/20) REF. NO andAREA Page Page Page Page Page Replacement Parts List CF-19CDBAXVM (2006/11/20) PART NO. DESCRIPTION Q'T Y MAIN PCB REF. NO and AREA Page Page Page Page Page AUDIO PCB IO PCB PAD PCB SW PCB LED-LEFT PCB PR PCB LED-RIGHT PCB SD PCB HSDPA PCB POWER SW PCB EXTENAL ANTENNA PCB BLUETOOTH PCB HDD FPC BATTERY FPC