20
Getting StartedUseful InformationTroubleshootingAppendix
Troubleshooting (Basic)Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the
“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact
Panasonic Technical Support (Îpage 29). You can also check the computer’s status in the PC Information Viewer
(Î Reference Manual “Troubleshooting (Advanced)”).
Starting Up
Cannot start up.
The power indicator or bat-
tery indicator is not lit.
zConnect the AC adaptor.
zInsert a fully charged battery.
zRemove the battery pack and the AC adaptor, then connect them again.
zRemove the USB device, or set [USB Port] or [Legacy USB Support] to [Disable] in
[Advanced] menu of the Setup Utility. The computer may not start up when certain
USB devices are connected.
The power is turned on but
“Warming up the system (up
to 30 minutes)” appears.
zThe computer is warming up before start up. Wait for the computer to start up (takes
up to 30 minutes). If, “Cannot warm up the system” is displayed, the computer failed
to warm up and does not start. In this case, turn off the computer, leave it in an envi-
ronment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on
the power once more.
Cannot turn on the computer.
The computer does not
resume from standby mode.
(The power indicator blinks
quickly in green.)
zLeave it in an environment of 5 °C {41 °F} or higher temperature for about an hour,
then turn on the power once more.
You have forgotten the
password.
zSupervisor Password or User Password: Contact Panasonic Technical Support
(Îpage 29).
zAdministrator password:
• If you have a password reset disk, you can reset the administrator password. Set
the disk and enter any wrong password, then follow the on-screen instructions and
set a new password.
• If you do not have a password reset disk, reinstall (Îpage 17) and set up Win-
dows, and then set a new password.
“Remove disks or other
media. Press any key to
restart” or a similar mes-
sage appears.
zA floppy disk is in the drive and it does not contain system startup information.
Remove the floppy disk and press any key.
zThis message may appear with some USB devices. Remove the USB device, or set
[USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the
Setup Utility.
zIf the problem persists after removing the disk, it may be a hard disk failure. Contact
Panasonic Technical Support (Îpage 29).
Windows startup and opera-
tion is slow.
zPress
F9
in the Setup Utility (Îpage 19 “To start the Setup Utility”) to return the
Setup Utility settings (excluding the passwords) to the default values. Start the
Setup Utility and make the settings again. (Note that the processing speed depends
on the application software, so this procedure may not make Windows faster.)
zIf you installed a resident software after purchase, turn off the residence.
zDisable Indexing Service in the following menu.
Click [start] - [Search] - [Change preferences] - [Without Indexing Service].
The date and time are incor-
rect.
zMake the correct settings. Click [start] - [Control Panel] - [Date, Time, Language,
and Regional Options] - [Date and Time].
zIf the problem persists, the internal clock battery may need to be replaced. Contact
Panasonic Technical Support (Îpage 29).
zWhen the computer is connected to LAN, check the date and time of the server.
zThe 2100 A.D. or later year will not be correctly recognized on this computer.
[Executing Battery Recali-
bration] screen appears.
zThe Battery Recalibration was canceled before Windows was shut down last time.
To start up Windows, turn off the computer by the power button, and then turn on.