Panasonic CU-C12CKP6, CU-C7CKP5, CU-C9CKP5, CU-C12CKP5 Setting the Timer, Convenience Operation

CS-C7CKP CU-C7CKP5 / CS-C9CKP CU-C9CKP5 / CS-C9CKP CU-C9CKP6 / CS-C12CKP CU-C12CKP5 / CS-C12CKP CU-C12CKP6

■Setting the Fan Speed

•Press 4 to select:-

FAN		–	Low Fan Speed
FAN		–	Medium Fan Speed
FAN		–	High Fan Speed
AUTO
FAN –	Automatic Fan Speed
	The speed of the indoor fan is adjusted
	automatically according to the operation.
	The indoor fan stops occasionally during
	cooling operation.

■Setting the Vertical Airflow Direction

• Press 5 or 6 to select:-

Cooling Model

COOL / DRY Operation			FAN Operation
AUTO			AUTO
36°		61°
Swing up/down			Move up/down
Automatically			Automatically
MANUAL			MANUAL
			Five stages of adjustment
Five stages of adjustment
can be made between			can be made between
14° ~ 36°.		0° ~ 61°.
	Heat Pump Model
COOL / DRY Operation			HEAT Operation
AUTO			AUTO
		– When the discharge air
			temperature is low such
			as at the start of heating
36°			operation, the air blows
			at horizontal level. As
			the temperature rises,
Swing up/down			the hot air blows at a
			downward direction.
Automatically
		– To stop this operation,
			press MANUAL.
MANUAL			MANUAL
Five stages of adjustment			Five stages of adjustment
can be made between			can be made between
14° ~ 36°.		0° ~ 61°.

■Setting the Horizontal Airflow Direction

• Adjust it manually

●Use this air conditioner under the following conditions:

Cooling Model

Unit in °C

DBT: Dry Bulb Temp	Indoor		Outdoor
WBT: Wet Bulb Temp	DBT	WBT	DBT	WBT
Maximum Temperature	32	23	43	26
Minimum Temperature	16	11	16	11

Heat Pump Model

Unit in °C

DBT: Dry Bulb Temp	Indoor		Outdoor
WBT: Wet Bulb Temp	DBT	WBT	DBT	WBT
Maximum Temperature-Cooling	32	23	43	26
(Maximum Temperature-Heating)	(30)	(-)	(24)	(18)
Minimum Temperature-Cooling	16	11	16	11
(Minimum Temperature-Heating)	(16)	(-)	(-5)	(-6)

●Notes

•If the unit is not going to be used for an extended period of time, turn off the main power supply. If it is left at the ON position, approximately 2.5 W of electricity will be used even if the indoor unit has been turned off with the remote control.

•If operation is stopped, then restart immediately, the unit will resume operation only after 3 minutes.

●Operation Details

COOL – Cooling Operation

•To set the room temperature at your preference cooling comfort.

AUTO – Automatic Operation

•Sense indoor temperature to select the optimum mode.

•Temperature is not displayed on the remote control during AUTO operation.

DRY – Soft Dry Operation

•A very gentle Cooling Operation, prior to dehumidification. It does not lower the room temperature.

•During Soft Dry operation, the indoor fan operates at Low fan speed.

HEAT – Heating Operation (for Heat Pump Model only)

•Heat is obtained from outdoor air to warm up the room. When the outdoor ambient air temperature falls, the heating capacity of the unit might be reduced.

•Defrosting Operation

Depend on the outdoor temperature, the operation occasionally stops to melt the frost on the outdoor unit.

FAN – Air Circulation Operation

(for Cooling Model only)

•When the room temperature reaches the set temperature, operation commences at Low airflow volume. It stops when the room temperature drops to 2°C below the set temperature.

(It is useful when using a heater).

8			OFF/ON
7	MODE	QUIET	POWERFUL	6

AIR SWING

	AUTO	MANUAL	FAN SPEED
1	1	2	3	3
	ON		SET
5	OFF		CANCEL	4
		TIMER		2

SETTING THE TIMER

Ensure that the current time is correct before setting the timer. The timer cannot be set if the time display is flashing.

■ON-TIMER Operation

To start the air conditioner operation automatically.

•Press 1 to set the operation.

•Press 2 to increase or decrease the time.

•Then press 3.

•To cancel this operation, press 4.

■OFF-TIMER Operation

To stop the air conditioner operation automatically.

•Press 5 to set the operation.

•Press 2 to increase or decrease the time.

•Then press 3.

•To cancel this operation, press 4.

●Timer Mode Operation Details

•When the ON-Timer is set, operation will start before the actual set time. This is to enable the room temperature reaches the set temperature at the set time.

Cooling Model		Heat Pump Model
COOL,DRY, –>15 minutes		COOL,DRY, –>15 minutes
AUTO	in advance	in advance
		HEAT, AUTO –>30 minutes
		in advance

•Once the ON/OFF Timer is set, operation will start/ stop at the set time everyday.

•The current time is not displayed when the timers are set.

•When both timers are used together, the TIMER mode indicator on the indoor unit remains lit even when the operation is stopped by the OFF-TIMER.

CONVENIENCE OPERATION

■Powerful Mode Operation

To obtain the set temperature quickly.

•Press 6.

∗Powerful mode indicator (orange) on the indoor unit will light up.

∗Powerful mode will operate for 15 minutes only.

• To cancel this operation, press once more.

●Powerful Mode Operation Details

• The changes of the temperature and airflow volume are automatic.

• The remote control display remains unchanged.

• If operation mode button is pressed, powerful operation will be cancelled.

• During FAN – Air circulation operation, the powerful operation are not available.

(cooling model only)

Powerful Mode	Temperature	Airflow
Operation		volume
	3°C lower
COOL / DRY	than set temp.	Super High
HEAT	3°C higher
(for Heat Pump	than set temp.	Automatic
model only)

■Quiet Mode Operation

To provide quiet operation.

• Press 7.

∗Quiet mode indicator on the indoor unit will light up.

•To cancel this operation, press once more.

●Operation Details

•Air flow sound will reduce during operation.

■Ionizer Mode Operation Produce negative ion for fresh air.

•Press 8.

∗ Ion mode indicator on the indoor unit will light up.

• To cancel this operation, press once more.

●Operation Details

• Air conditioner ON:

Provide negative ion during operation.

• Air conditioner OFF:

Provide negative ion with FAN operation.

• If blinking, press 8 twice.

If still blinking, please call service.

34