EQ-500

PRECAUTIONS FOR PROPER USE

Wiring

Make sure that the power supply is off while wiring.

Check all wiring before applying power since incorrect wiring may damage the internal circuit. Also, carefully tighten the terminal screws so that the wires of adjacent terminals do not touch.

The mounting hole for the terminal cover fixing screws inclines 70 degrees to the terminal cover, as shown in the figure below. To avoid damaging this product or screw, take care when tightening or loosening a screw.

Screw for terminal cover fixing

Screwdriver

To maintain water-resistance, the cable should have an outer diameter between "9 to "11 mm "0.354 to "0.433 in with a smooth covering material that allows the attached conduit connector to be securely tightened; the tightening torque of the screw should be of 1.5 to 2.0 N m.

Verify that the supply voltage variation is within the rating.

If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground.

In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.) terminal of the equipment to an actual ground.

Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction.

If an external surge voltage exceeding 4 kV is impressed (DC- voltage type: 1 kV), the internal circuit will be damaged, and a surge suppressing element should be used.

Prepare the cable end as shown below.

Conduit connector construction and cabling

 

 

37 mm

 

 

1.457 in

 

Power supply

 

 

Conduit connector

 

 

Output

 

Gland packing (Note)

Gland

25 mm

 

 

0.984 in

Note: When assembling the conduit connector, pay attention to the direction of the gland packing.

Furthermore, in order to maintain water-resistance, fit the gland packing such that the seating surface of the gland packing contacts the packing holder part of the terminal cover evenly.

The size of conduit is M201.5.

If pressure terminals are to be used, affix the connected pressure terminals to a terminal (M3.5 screw).

Dimensions of the suitable crimp terminals

 

 

 

 

 

 

 

 

(Unit: mm in)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Round type

 

 

 

Y-shaped type

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

"3.6

22 0.866

 

 

 

 

 

3.6 0.142

 

22 0.866

 

 

 

 

 

 

 

"0.142

 

 

 

 

or less

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or less

 

 

 

 

 

 

or more

 

 

 

 

 

 

 

 

10 0.394

 

 

 

or more

 

 

 

 

 

 

 

10 0.394

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or less

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or less

 

 

 

 

7.5 0.295

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

0.276

7.5 0.295

 

 

 

 

7

 

0.276

or less

 

 

 

 

 

17 0.669

 

 

 

or less

or less

 

 

17 0.669

 

 

 

 

or less

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or less

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or less

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(After crimping)

 

 

 

 

 

 

 

 

(After crimping)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: Use crimp terminals with insulating sleeves.

Recommended crimp terminal: Nominal size 1.253.5 0.0490.138.

The tightening torque for the terminal screws should be 0.3 to 0.5 N m.

Part description

Stability indicator (Green)

 

Distance adjuster (2-turn)

OFF-delay timer adjuster (Note 2)

Adjuster indicator

ON-delay timer adjuster (Note 2)

Operation indicator (Orange)

Operation mode switch (Note 1)

Notes: 1) The operation mode switch of the DC-voltage type is the DIP switch. Refer to ‘DC-voltage type’ of ‘Operation mode switch’ for details.

2) Incorporated on EQ-5Tonly.

Operation mode switch

Multi-voltage type (L-ON / D-ON mode only)

Operation mode switch

Description

Detection-ON mode is obtained when the switch is turned fully clockwise (L side).

Detection-OFF mode is obtained when the switch is turned fully counterclockwise (D side).

Note: Turn the operation mode switch gradually and lightly with the attached screwdriver. Turning with excessive strength will cause damage to the adjuster.

DC-voltage type

L-ON / D-ON mode

 

 

 

L

 

 

 

 

 

 

 

D

BGS / FGS mode

 

 

 

BGS

 

 

 

 

 

 

 

FGS

Timer mode

 

 

 

OFF

 

 

 

 

 

 

 

Timer ON

Not used

 

 

 

N.C.

 

 

 

 

 

 

 

N.C.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BGS / FGS function (DC-voltage type only)

DC-voltage type sensor incorporates BGS / FGS function. Select either the BGS or FGS function depending on the positions of the background and sensing object.

BGS / FGS function is set with the operation mode switch.

Depends on a selection of either BGS or FGS function, the out- put operation changes as follows.

Detectable range

 

Setting distance

Non-detectable area

 

L-ON

ON

OFF

BGS

ON

D-ON

OFF

 

L-ON

ON

OFF

FGS

 

D-ON

ON

OFF

 

08/2005

201

 

Page 8
Image 8
Panasonic EQ-500 Series manual Precautions for Proper USE, Wiring, Part description, Operation mode switch

EQ-500 Series specifications

The Panasonic EQ-500 Series is a sophisticated line of electronic products that showcases Panasonic's commitment to innovation, user convenience, and sustainability. These models cater to various user needs, from audio-visual solutions to home appliances, and are designed with features that enhance overall functionality and efficiency.

One of the standout characteristics of the EQ-500 Series is its integration of advanced connectivity options. With built-in Bluetooth and Wi-Fi capabilities, users can seamlessly connect their devices, stream content, and share information easily. This level of connectivity ensures that the devices can interact with smart home systems and other electronic gadgets, providing a comprehensive user experience.

In terms of audio, the EQ-500 Series features high-quality sound systems that deliver clear and immersive audio. These devices come equipped with advanced digital signal processing technology, ensuring that users can enjoy their favorite music, movies, or shows with rich sound quality. The inclusion of surround sound capabilities further enhances the listening experience, making it ideal for home theater setups.

Another significant aspect of the EQ-500 Series is its energy-efficient design. Panasonic has prioritized environmentally friendly technologies, and the devices feature energy-saving modes that significantly reduce power consumption without compromising performance. This commitment to sustainability makes the EQ-500 Series a smart choice for eco-conscious consumers looking to minimize their environmental impact.

User interface is another focus in the EQ-500 Series. The products are designed with intuitive controls and user-friendly interfaces, allowing for easy navigation and operation. A combination of touch-sensitive controls and traditional buttons ensures that users can easily interact with the devices, regardless of their technological proficiency.

Durability and build quality are also essential characteristics of the EQ-500 Series. Panasonic employs high-quality materials and rigorous testing standards to ensure that their products withstand daily use while maintaining performance and aesthetic appeal. The sleek designs fit well in any modern home, making them not just functional but also stylish additions to living spaces.

Overall, the Panasonic EQ-500 Series exemplifies a blend of cutting-edge technology, superior audio-visual capabilities, energy efficiency, and user-centric design. As consumers increasingly seek devices that enhance their digital lifestyle while being environmentally conscious, the EQ-500 Series stands out as a versatile and reliable option. Whether for entertainment or daily tasks, these products represent the future of home electronics, tailored to meet the evolving needs of users worldwide.