Bikini (see fig. 10)

It is recommended to use the pop- up trimmer for proper shave.

Cleaning

(see fig. 5)

For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while pre- venting odors or bacteria from devel- oping, and maintain the cutting per- formance.

With the outer foils in place, apply some hand soap onto the outer foils. Turn the shaver on and turn off after few seconds.

Next, press the outer foil frame re- lease buttons to remove the outer foil frame and rinse the inner blade/outer foils under running water or in a ba- sin.

DO NOT USE BOILING WATER. Next, close the outer foil frame and dry it gently. After the shaving head is dry, place the protective cap.

Replacing shaving head components

It is recommended that you replace the outer foil at least once every year and the inner blade at least once every two years to maintain your shaver’s cutting performance.

Replacing the outer foil (see fig. 2, 3)

Press the outer foil frame release but- tons to remove the outer foil frame . Then, squeeze the front and the back

side of the foil frame and lift up one of the two knobs on the outer foil.

Inserting the new outer foil

Slip the foil into the frame and guide the plastic edges onto the hooks in the foil frame until it clicks into the shaver.

Replacing the inner blade

(see fig. 2, 4)

Squeeze the outer foil release but- tons and lift the outer foil frame up- ward to remove it. Remove the inner blade by grasping it firmly at both ends and pulling straight away from the shaver. To insert the new inner blade, hold the blade at both ends and press downward until it snaps into the shaver.

ATTENTION:

The product you have purchased is powered by a nickel cadmium battery which is recyclable. At the end of its useful life, under vari- ous state and local laws, it is ille- gal to dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle this battery.

How to remove the built-in rechargeable battery before disposal of shaver

The battery in this shaver is not in- tended to be replaced by consumers. However, the battery may be re- placed at an authorized service center. The procedure described be- low is intended only for removal of the rechargeable battery for the purpose of proper disposal.

WARNING:

Do not attempt to replace the bat- tery for the purpose of reusing the shaver. This could result in the risk of fire or electric shock.

1.Remove four screws (a). (see fig. 11)

2.Remove two screws (b). (see fig. 12)

3.Pull the housing (c) out of the end cap (d). (see fig. 13)

4.Remove two screws (e) inside of the end cap and pull the battery. (see fig. 14)

5.Using a flat screwdriver (f), and insert into the space (g) to remove the battery. (see fig. 15)

ATTENTION:

This laws of various states and municipalities restrict disposal of rechargeable batteries (and prod- ucts from which such batteries have not been removed) in ordi- nary household waste. Please comply with your local laws. If you are not certain as to proper dis- posal, please contact your local sanitation department.

Caution

Do not charge the shaver where the temperature is below 0°C (32°F) or above 40 °C (104°F), where it will be exposed to direct sunlight or a heat source, or where there is a lot of moisture.

Use only the included shaver charging stand RE3-40 to charge the ES2206 shaver.

Dry the shaver completely before setting it in the charging stand.

Keep the charging stand away from water and handle it only with dry hands. Do not use an extension cord to connect the charging stand to an outlet.

The shaver may not immediately begin to charge after being placed into the charging stand after use. Allow the shaver to sit in the charg- ing stand for a few minutes and check again to make sure that it is being charged.

Store the charging stand in a dry area where it will be protected from damage.

8

9

Page 5
Image 5
Panasonic ES2206 Cleaning, Replacing shaving head components, Replacing the outer foil see, Inserting the new outer foil