to blink (Differs depending on usage.).
[for ES7035, ES7034, ES7032] The charge status lamp will glow when the shaver is being charged. It will blink when charging is com- pleted (see fig. 2 (D)).
You can fully charge the shaver in 1 hour if the low battery indicator blinks (see fig. 2 (C)).
The unit can be used once or twice more after the low battery indicator starts to blink.
A full charge will supply enough power for approx. 14 shaves (3 min- utes per shave for a normal beard). Before travelling, charge your shaver fully for 1 hour if you will not be tak- ing the adaptor with you.
In case your shaver is without charge, you may quick charge it for 1 shave in about 5 minutes.
Using your shaver
Caution – The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foil for dam- age. To avoid personal injury, do not use if the foil or other parts of the shaving head is damaged.
Disconnect the power cord from the shaver. Depress the switch lock button and slide the On/Off switch upward to turn the shaver on.
Hold the shaver at a right angle (90°) to your skin (see fig. 3). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin be- comes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.
System outer foil (see fig. 4)
System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face.
The slit blade catches and cuts longer and lying hairs easily.
For wet shaving
Put a thin layer of shaving foam on your face which works as a lubrica- tor. Shaving foam is the most suit- able among many other shaving aids (gel, soap, cream, etc.). Do not put a thick layer of shaving foam as it may affect shaver’s performance. If the shaving head is clogged with foam, simply rinse it under running water.
Using the trimmer
(see fig. 5)
Slide the trimmer handle up to open the trimmer.
Place the trimmer at a right angle to your skin and move it downward to trim sideburns.
Cleaning your shaver
(see fig. 6)
Warning – To prevent electric shock or personal injury, discon- nect the power cord from the shaver before cleaning with water.
For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while pre- venting odors or bacteria from devel- oping, and maintain the cutting per- formance.
With the system outer foil in place, apply some hand soap onto the outer foil.
Turn the shaver on and pour some water over the outer foil.
After about
Remove the foil frame and clean it with running water.
Wipe off any moisture from the shaver with a dry cloth and remove the protective cap to allow the sys- tem outer foil to dry completely.
Replacing shaving head components
It is recommended that you replace the system outer foil at least once a year and the inner blade at least once every 2 years to maintain your shav- er’s cutting performance.
Replacing the system outer foil
(see fig. 7)
Squeeze the system outer foil re- lease buttons and lift the system outer foil upward to remove it. To in- sert the new system outer foil, press down until it snaps into place.
Replacing the inner blades (see fig. 8)
Squeeze the foil frame release but- tons and lift the foil frame upward to remove it. Remove the inner blade one at a time by grasping it firmly at both ends and pulling straight away from the shaver.
Do not touch the metal parts of inner blades.
To insert the new inner blade, hold the blade one at a time at both ends and press downward until it snaps into the shaver.
ATTENTION:
A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call
8 | 9 |
