rection of your beard.You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pres- sure does not provide a closer shave.
System outer foil (see fig. 5)
System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face.
The slit blade catches and cuts longer and lying hairs easily.
Turn the shaver on and pour some water over the outer foil.
After about
Remove the foil frame and clean it with running water.
Wipe off any moisture from the shaver with a dry cloth and remove the protective cap to allow the sys- tem outer foil to dry completely.
Replacing shaving head components
ATTENTION:
2 nickel metal hydride batteries that are recyclable power the prod- uct you have purchased. Please call
pick), four screws (e), and the panel cover (f).
5.Remove the screw (g) and the bottom cover (h).
6.Remove the back panel (i).
7.Remove the batteries from the battery block (j).
WARNING:
Do not attempt to replace the bat- tery for the purpose of reusing the shaver. This could result in the risk of fire or electric shock.
Using the trimmer
(see fig. 6)
Slide the trimmer handle up to open the trimmer.
Place the trimmer at a right angle to your skin and move it downward to trim sideburns.
Cleaning your shaver
(see fig. 7)
Warning – To prevent electric shock or personal injury, discon- nect the power cord from the shaver and turn the shaver off be- fore cleaning.
For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while pre- venting odors or bacteria from devel- oping, and maintain the cutting per- formance.
With the system outer foil in place, apply some hand soap onto the outer foil.
It is recommended that you replace the system outer foil at least once a year and the inner blade at least once every 2 years to maintain your shav- er’s cutting performance.
Replacing the system outer foil (see fig. 8)
Squeeze the system outer foil re- lease buttons and lift the system outer foil upward to remove it. To in- sert the new system outer foil, press down until it snaps into place.
Replacing the inner blades (see fig. 9)
Squeeze the foil frame release but- tons and lift the foil frame upward to remove it. Remove the inner blade, one at a time, by grasping them firmly at both ends and pulling straight away from the shaver. To insert the new inner blade, hold the blade, one at a time, at both ends and press downward until it snaps into the shaver.
How to remove the
(see fig. 10)
The batteries in this shaver are not intended to be replaced by consum- ers. However, the batteries may be replaced at an authorized service center. The procedure described be- low is intended only for removal of the rechargeable batteries for the purpose of proper disposal.
Always make sure that the batteries have been removed from the shaver before disposing of it.
1.Disconnect the power cord from the AC outlet, and remove the power cord from the shaver.
2.Remove the outer foil frame and the inner blades.
3.Remove the trimmer driving bar (a), slit blade driving bar (b) and two screws (c).
4.Remove the four screw covers (d) (using something like a tooth-
Caution – To prevent personal injury or damage to the product,
•Do not charge the shaver where the temperature is below 0°C (32°F) or above 40°C (104°F), where it will be exposed to direct sunlight or a heat source, or where there is a lot of moisture.
•Use only the included power cord
•Dry the shaver completely before charging it.
•Keep the power cord away from wa- ter and handle it only with dry hands.
•Grip the plug when disconnecting the power cord from an AC outlet; tugging on the power cord may damage it.
•Store the power cord in a dry area where it will be protected from dam- age.
•Do not pull, twist, or severely bend the power cord.
8 | 9 |
8 | 9 |
