Panasonic Network Adaptor manual Technical data

FP-e Series

Technical data

■General specifications

Item		Description
Rated voltage	24 V DC
Operating voltage range	21.6 to 26.4 V DC
Allowed momentary power off time	10 ms
Ambient temperature	0 to +55¡C
Storage temperature	Ð20 to +70¡C
Ambient humidity	30 to 85%RH (non-condensing)
Storage humidity	30 to 85%RH (non-condensing)
	Input terminals (COM, X0 to Xn)	Power supply terminal, Function earth
	Output terminals (Y0 to Y4)	Input terminal (A0, A1)	500 V AC for 1 minute
		COM. (RS232C) terminal
Breakdown voltage
	Output terminal (Y5)	Power supply terminal, Function earth
		Input terminal (COM, X0 to Xn, A0, A1)	1500 V AC for 1 minute
		COM. (RS232C) terminal
	Input terminals (COM, X0 to Xn)	Output terminals (Y0 to Y4)	500 V AC for 1 minute
	Input terminals (COM, X0 to Xn)	Power supply terminal, Function earth
Insulation resistance	Output terminals (Y0 to Y5)	Input terminal (A0, A1)	Min. 100 M
		COM. (RS232C) terminal
			(measured with 500 V DC)
	Input terminals (COM, X0 to Xn)	Output terminals (Y0 to Y5)
Vibration resistance	10 to 55 Hz, 1 cycle/min.
	Double amplitude: 0.75 mm, 10 min. on X, Y, and Z axes
Shock resistance	98 m/s2 or more, 4 times on X, Y, and Z axes
Noise resistance	1000V (p-p) with pulse widths 50 ns and 1 µs (based on in-house measurements)
Operating condition	Free from corrosive gases and excessive dust
Current consumption	200 mA or less (24 V DC)
Protection	IP66-compliant front section (Only when a rubber packing is used.)
Mass	Approx. 130 g

■DC input specifications (X0 to X7)

Item			Description
Number of input		8 points (6 points for thermocouple input type)
Insulation method		Optical coupler
Rated input voltage		24 V DC
Operating voltage range		21.6 to 26.4 V DC
Rated input current		Approx. 4.3 mA
		8 points/common (6 points/common for
Input points		thermocouple input type)
per common		Either the positive or negative of the input power
		supply can be connected to common terminal.
ON voltage/ON current		19.2 V or less/4 mA or less
OFF voltage/OFF current		2.4 V or more/1 mA or more
Input impedance		Approx. 5.1 k	(X0, X1)
		Approx. 5.6 k	(X2 to X7)
		50 µs or less (X0, X1) Note 1)
	OFF to ON	100 µs or less (X2 to X5) Note 1)
Response		2 ms or less	(X6, X7)
time		50 µs or less (X0, X1) Note 1)
	ON to OFF	100 µs or less (X2 to X5) Note 1)
		2 ms or less	(X6, X7)
Operating mode indicator		LCD display (I/O monitor mode)

Note 1) X0 through X5 are inputs for the high-speed counter and have a fast response time. If used as normal inputs, you should insert a timer in the program as chattering and noise may be interpreted as an input signal.

Also, the above specifications apply when the rated input voltage is 24V DC and the temperature is 25¡C.

■Thermocouple input specifications

Item	Description
Number of input	2 points (CH0: WX1, CH1: WX2)
Temperature sensor type	Thermocouple type K
Input range	Ð30.0 to 300.0¡C ∗1) (Ð22 to 572¡F)
Accuracy	±0.5%FS±1.5¡C (FS = Ð30 to 300¡C)
Resolution	0.1¡C
Conversion time	250 ms/2CH ∗2)
	Between internal circuit and thermocouple input
Insulation method	circuit: noninsulated ∗3)
	Between CH0 and CH1 of thermocouple input:
	PhotoMOS insulation
Detection function of	Available
wire disconnection

∗1) Temperature can be measured up to 330¡C (626¡F). When the measured temperature exceeds 330¡C (626¡F) or the thermocouple wiring is disconnected, ÒK20000Ó is written to the register.

∗2) Temperature conversion for thermocouple input is performed every 250 ms. The conversion data is updated on the internal data register after the scan is completed.

∗3) The internal circuit and thermocouple input circuit are not insulated. Therefore, use the nongrounding type thermocouples and sheath tubes.

6 Clearwater Tech - Phone: 800.894.0412 - Fax: 208.01/2004368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com