![](/images/new-backgrounds/1233358/23335819x1.webp)
Tape Operation
Search System
For each recording, an invisible index mark is placed on the tape.
A program index and information are also included for timer recordings.
These marks are used to access or scan recordings.
Index Search
Repeat Play
Set to playback a recording over and over. 1 Press ACTION to display menu.
2 | MENU |
| Press | to select |
SET UP VCR |
| |||
SET UP CLOCK |
| “SET UP VCR,” | ||
| SET UP CHANNEL | |||
| IDIOMA/LANGUE : ENGLISH | and press . | ||
| VCR’S OUTPUT CH: 3 | |||
| SELECT : | SET: |
|
|
| EXIT : ACTION |
|
|
|
Tape Operation
Tape Select
Select your tape length so the tape position and amount of tape remaining are properly displayed. (See “Tape Position and Tape Status Display” section below.)
1 Press ACTION to display menu. | ||||
2 | MENU | Press | to select | |
SET UP VCR | ||||
“SET UP VCR,” | ||||
| SET UP CLOCK | |||
| SET UP CHANNEL | |||
|
|
| ||
| IDIOMA/LANGUE : ENGLISH |
|
|
Commercial Skip
VCR fast forwards (skips) over 1, 2, or 3 minutes of recorded tape as desired.
1 Press CM/ZERO in Play mode.
•Press CM/ZERO repeatedly to change skip time as shown below.
PLAY
• Tape Operation
1
2
INDEX SEARCH
ENTER INDEX NUMBER :1 USING 1- 9 KEYS
FORWARD SEARCH :FF REVERSE SEARCH :REW
EXIT :SEARCH
INDEX SEARCH
FORWARD SEARCH :FF REVERSE SEARCH :REW
Press SEARCH* to display SEARCH in Stop or Play mode, and then press
NUMBER keys to select
recording number.
•To calculate number, see below.
Press FF or REW to start search.
Play begins at search end. To search forward or back 1 index, press FF or REW while screen left is displayed (10 sec.).
•To cancel, press PLAY or STOP.
3 | SET UP VCR | Press | to select | |
REPEAT PLAY | : OFF | “REPEAT PLAY,” | ||
AUTO | : OFF | |||
| FRONT DISPLAY | : ON | and press | to set |
| AUTO VCR/TV | : ON | ||
| TAPE SELECT | : | “ON” or “OFF.” | |
|
|
| ||
| SELECT : | SET: | ON :Play repeats at tape end | |
| EXIT : ACT I ON |
|
or if unrecorded portion over 30 sec. is detected.
4 Press ACTION
to return to normal screen.
Zero Search
To quickly return to a specified tape location.
VCR’S OUTPUT CH: 3 | and press . |
| ||||||
SELECT : | SET: |
|
|
|
|
|
| |
EXIT | : ACTION |
|
|
|
|
|
|
|
| SET UP VCR | Press |
| to select | ||||
3 REPEAT PLAY | : OFF | “TAPE SELECT,” and | ||||||
AUTO | : OFF | |||||||
FRONT DISPLAY | : ON | press |
| to set | ||||
AUTO VCR/TV | : ON |
| ||||||
TAPE SELECT | : |
| ||||||
|
|
|
| |||||
SELECT : | SET: |
|
|
| ||||
EXIT | : ACT I ON |
|
|
|
| |||
|
|
|
•Select
4 Press ACTION
to return to normal screen.
1st Press 1 min Skip
2nd Press | 2 min Skip |
3rd Press 3 min Skip
•No indication appears.
To Calculate Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1 | 2 | 3 | 4 |
| 5 | 6 | 7 |
|
|
|
|
|
|
|
|
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1 | 2 | 3 | 4 | 5 | 6 | 7 |
1 Press DISPLAY during play to display Counter.
2 | PLAY 12 : 0 0AM | Press COUNTER RESET |
0 : 00 : 00 | on remote at desired | |
SP | ||
|
| position to reset to |
|
| “0:00:00”. |
3 | Continue to record, playback, etc. | |
4 | Press STOP. |
|
Tape Position and Tape Status Display
To find out the present tape position and amount of tape remaining.
Tape position is displayed incorrectly in the following cases:
•If
•If the correct tape length is not selected. (See “Tape Select” section above.)
1Press TAPE POSITION to detect tape position.
NOTE: indicates start points of each recording.
Note
•If Index Search is started very close to an index mark, that index mark may not be counted in the search.
5 | REW | 12 : 3 0AM CH 02 | Press CM/ZERO in |
| 0 : 30 : 30 | Stop mode to start | |
| SP |
ZERO SEARCH.
• Unit will go into FF or REW
mode and stop at the last point the Counter was set to 0:00:00.
STOP 12 : 3 1AM CH 02
0: 00 : 00
SP
DETECTING TAPE POSITION
SP
R 120 MI N.
BEGIN END
•“DETECTING TAPE POSITION” only appears the first time a cassette is inserted and it takes several seconds for correct indication to appear.
•The present tape position indication and amount of tape remaining (according to tape speed) are displayed.
Tape remaining time display may not be precise.
2 Press TAPE POSITION (or wait 5 seconds) to return to normal screen.
| *Important: If a remote control button does not work when pressed, |
| press the VCR button on the remote and try the button again. |
- 6 - | - 7 - |