Panasonic PV-V462 Press SAP/ Hi-Fi repeatedly, Do a recording, Examples of Program End Search

STOP 12 : 3 1AM CH 02 0 : 00 : 00

SP

*Important:

Confirm code entry,

3

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TV and Cable Box/DSS functions.

1 Find your TV and Cable Box/DSS Receiver Brand Code Number from those shown below.

2 Setup for TV control, ➛ hold down TV button,

➛ enter code with NUMBER keys.

Setup for Cable or DSS control, ➛ hold down DSS/CABLE button,

➛ enter code with number keys.

• If code number is 100 or greater,

➛ press 100 key, then other digits. E.g., press 100 - 0 - 2 for 102.

Advanced Connections

Audio/Video connection

If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR to them to receive higher quality picture and sound.

• Multi-Brand

MTS Broadcast

Connection

Make the Audio/Video Connection as shown on page 3.

•You can use a TV connected to a Stereo amp and speakers instead of a Stereo TV.

VHS Hi-Fi Stereo System

Audio Mode for Recording

1 Press SAP/ Hi-Fito display audio mode. (Display disappears after 5 seconds.)

• MTS Broadcast

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.

Tape Operation

Repeat Play

Set to playback a recording over and over.

1 Press ACTION to display menu.

Commercial Skip

VCR fast forwards (skips) over 1~3 minutes of recorded tape.

1 Press CM/ZERO in Play mode.

• Tape Operation

Control

TV

2 Press SAP/ Hi-Fi repeatedly

•

Index Search

Program End Search

2					Press
	VCR		CLOCK	CHANNEL
	REPEAT	PLAY		:OFF	to select REPEAT PLAY
	REMOTE WARNING			:ON

• Press CM/ZERO repeatedly to change

➛press POWER to turn your TV on or off.

•See table below for controllable functions in each mode.

IN FROM ANT.

VCR

AUDIO OUT

R	AUDIO IN
L	R
OUT TO TV	L

VIDEO OUT

TV

VHF/UHF

Feature •

R

L

VHF/UHF

VCR

AUDIO OUT

R

L

R

Stereo Amplifier

AUDIO IN

STEREO	to select desired mode.
SAP	• Refer to “Receivable
MONO
	Broadcast Types” on page 4.

•Arrow indicates selection.

3 Do a recording.

VHS Hi-Fi Stereo

1		SEARCH
	INDEX		PROGRAM END

ENTER INDEX NUMBER :1

USING 1- 9 KEYS

FORWARD SEARCH :FF

REVERSE SEARCH :REW

NEXT :SEARCH

EXIT :STOP

Press SEARCH* to display SEARCH in Stop or Play mode, and then press NUMBER keys to select recording number.

•To calculate number, see below.

Press FF or REW on

Locates end point of recording for continuity.

1 Press SEARCH twice to display SEARCH

in Stop or Play mode.

2		SEARCH		Press FF on the remote
	INDEX		PROGRAM END	to start PROGRAM
				END SEARCH.
	SEARCH START :FF			• To cancel, press

AUTO SHUT- OFF		:OFF	and press to set ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH		:3	or OFF.
SELECT :	SET :		ON : Play repeats at
EXIT : ACT I ON

tape end or if unrecorded portion over 30 sec. is detected.

3 Press ACTION to return to normal screen.

skip time as shown below.

PLAY

1st Press 1 min Skip

Notes • Repeat setup after remote battery replacement.

L

See p. 5 of “Basic Operations” Instruction book.

the remote to start

EXIT :SEARCH STOP or PLAY.

•Remote will not control every TV, cable box, or DSS made by the manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.

VIDEO IN

Advanced

OUT TO TV

System

2 INDEX SEARCH

search.

Play begins at search end. To search forward or back 1 index, press

Examples of Program End Search.

Fig. 1

Zero Search

3rd Press 3 min Skip

• No indication appears.

Using Multi-Brand Control

After remote is set up, you can select VCR, TV, or DSS/CABLE for the desired function. Press VCR, or TV, or DSS/CABLE on the remote.

(Table below shows available unit buttons for each mode.)

Unit	VCR	TV	CABLE/ DSS
Mode
VCR	All	VOL UP/DOWN
TV	VCR/TV, PLAY, STOP,	POWER, INPUT, number
	EJECT, SAP/ Hi-Fi, DISPLAY,	keys, ENTER, CH UP/
	FF, REW, PAUSE/SLOW,	DOWN, VOL UP/DOWN

1 Connect the VCR’s VIDEO OUT jack to the TV’s VIDEO IN jack.

2 Connect VCR’s L/R AUDIO OUT jacks to the TV’s L/R AUDIO IN jacks.

Connections

Receivable Broadcast Types

The following are possible audio broadcast types and on-screen displays.

The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow.

To display the broadcast signal being received, ➛ press DISPLAY*.

Audio Mode for Playback

1 Start playback.

See p. 5 of “Basic Operations” Instruction book.

2 Press SAP/ Hi-Fi to display audio mode. (Display disappears after 5 seconds.)

FORWARD SEARCH :FF REVERSE SEARCH :REW

FF or REW on the

remote or VCR while

screen left is displayed

(10 sec.).

•To cancel, press STOP or PLAY.

Program 1 INDEX Program 2 or BLANK

the current tape position Press SEARCH button

	End Point
FF

Fig. 2
INDEX	Program 1	BLANK	INDEX	Program 2	BLANK
		the current tape position
		Press SEARCH button
			FF		End Point

To quickly return to a specified tape location.

1 Press DISPLAY during play

to display Counter.

2	PLAY 12 : 0 0AM	0 : 00 : 00	Press RESET
			COUNTER at desired
		SP
			position to reset to
			“0:00:00”.

CABLE/		REC, SPEED, CM/ZERO,		POWER, ENTER, NUMBER
		COUNTER RESET, TAPE	VOL UP/DOWN
				keys (except 100key),
DSS		POSITION
				CH UP/ DOWN
Notes	• Not all functions listed may be controllable.

•In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.

TV Brand Code Numbers
Panasonic	01, 02 Sylvania	05 JVC	11

3 Set the VIDEO/TV selector of your TV (Monitor/Receiver) to “VIDEO.”

MTS Stereo and SAP broadcast	STOP 12 : 0 0AM	CH 02
Multi-channel Television Sound Stereo (main language)	STEREO	0 : 00 : 00
and Secondary Audio Program (sub language)		SP
	SAP
broadcasts are being received simultaneously.	MONO

Select STEREO or SAP audio mode.

3

H I F I : L/R

H I F I : L

H I F I : R

NORMAL

• Arrow indicates

Press SAP/ Hi-Fi repeatedly to select desired mode.

• Select “HIFI(L/R)” or

“HIFI(L)” or “HIFI(R)” to

listen to stereo recordings in

stereo sound.

Select “NORMAL” for

monaural sound.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

1 2 3 4 5 6 7

Fig. 3
		the current tape position
		Press SEARCH button
	INDEX	Program 1	BLANK	Program 2

		If search
End Point	FF	exceeds a few
		seconds in
		BLANK area.

3	Continue to record, playback, etc.
4	Press STOP.
5	REW 12 : 3 0AM CH 02	Press CM/ZERO in Stop
	0 : 30 : 30	mode to start ZERO
	SP

SEARCH.

Quasar	01, 02	Sharp	06, 07	Hitachi	12
RCA	03	Sony	08	Mitsubishi	07, 13
GE	03	Toshiba	09	Samsung	14
Zenith	04	Sanyo	10	Gold Star	15, 16, 17
Magnavox	05	Fisher	10
Cable Box Brand Code Numbers
Archer	05, 06, 01, 44, 63, 91, 126		Quest		05, 06
Cabletenna		01, 44, 63, 91, 126	Radio Shack		51, 44, 59, 75, 126
Cableview	63, 44, 42, 30, 52, 04, 124, 126		RCA		16, 17, 97, 109
Century		51, 44, 59, 75, 126	Realistic		51, 44, 59, 75, 126
Citizen	63, 44, 42, 30, 52, 04, 124, 126		Recoton		51, 44, 59, 75, 126

■ With a Cable Box (VCR Cable Box)						You Can	You Cannot
				TV		• view any	• record
ANT	AUDIO IN FROM ANT.			IN OUT		(including	scrambled
or	R					scrambled)	channels.
			CABLE BOX	R	AUDIO	channel.
CATV	L	VHF/UHF		L
	VIDEO	OUT TO TV	IN OUT		VIDEO	• use VCR
	IN 1 OUT				VHF/UHF
						Remote
		VCR				Control to

MTS Stereo broadcast	STOP 12 : 0 0AM	CH 02
Multi-channel Television Sound Stereo broadcast.	STEREO	0 : 00 : 00
		SP
Select STEREO audio mode.	SAP
	MONO

•If stereo broadcast is weak and display flickers, select MONO audio mode for possibly better results.

selection.

Notes

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

1 2 3 4 5 6 7

Upon locating end point,

➛search continues 7 sec. past end point,

➛tape rewinds to 10 sec. before end point,

➛tape plays to end point and stops.

Notes

• If Program End Search is started very

close to an index mark, that mark may be

• Unit will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.

	Curtis			08, 09, 61, 53, 87	Regal	14, 15, 28, 41, 102, 103, 104, 108, 130
	Diamond			01, 44, 63, 91, 126	Regency		28, 130
	Drake			67	Rembrandt		01, 32, 39, 42, 44, 63, 126
	Eagle			13, 22, 58, 62, 20, 40, 26, 107	Salora		68
	Eastern			28, 130	Samsung		05, 32, 40, 42, 06
	GC Brand			63, 44, 42, 30, 52, 04, 124, 126	Scientific Atlanta		08, 09, 61, 53, 87
	Gemini			04, 124	Sheritech		27
	General Electric		...............................................	57, 01	Signal		26, 112
	General Instruments ..			01, 02, 03, 04, 34, 55, 83, 106,	SL Marx	32, 40, 42, 06, 43, 44, 52, 63, 126
			65, 67, 68, 115, 117, 118, 124, 91		Sprucer		16, 17, 97, 109
	Hamlin	14, 15, 28, 41, 102, 103, 104, 108, 130			Standard Components		32, 39, 42, 44, 126
	Hitachi			31	Stargate ..	32, 40, 63, 44, 42, 30, 52, 04, 06, 124, 126
	Jasco			04, 124	Sylvania		19
	Jerrold			01, 02, 03, 04, 34, 55, 83, 106,	Teknika		74
			65, 67, 68, 115, 117, 118, 124, 91		Telecaption		77, 127
	Macom			31	Teleview		32, 40, 42, 06
	Magnavox			26, 112	Texscan		18, 19
	Matsushita			16, 17, 97, 109	Tocom		33, 34, 01, 42, 66, 91
	Movietime			32, 39, 42, 44, 126, 38, 40	Toshiba		36
	NEC			38, 40, 32	Uniden Satelite		65
	NOVAVISION	.................................		08, 09, 61, 53, 87	Unika		01, 44, 63, 91, 126
	NSC			38, 40, 32	Universal		42, 43, 44, 52, 63, 126
	Oak			46, 11, 129	Videoway		07, 23, 50, 129
	Oak Sigma			46, 11, 129	Vid Tech		64
	Panasonic			16, 17, 97, 109	Vidtek		64
	Philips			07, 13, 20, 23, 24, 50, 128, 129	Viewstar		13, 22, 58, 62, 20, 40, 26, 107
	Pioneer			05, 06	Zenith		07, 23, 50, 129
	Pulsar			63, 44, 42, 30, 52, 04, 124, 126
	DSS Brand Code Numbers
	Toshiba			92	Panasonic		96
	Hitachi/ Hughes		....................................................	93	RCA		97
	Magnavox/ Uniden 1			94	Sony		98, 105
	Magnavox/ Uniden 2			95
Important		•	Due to changes in infra-red commands used by manufacturers, some brands have
Notes			several codes. If your unit does not respond to the first code, please try the next one.
		•	Some TV, Cable Box and DSS Box brands require you to turn on the power manually.

						select
						channels
						without using
						Multi-brand
						control feature.
■ Connect With Two Cable Boxes						You Can	You Cannot
			VCR		•	record and view	•	view channel
CABLE BOX		AUDIO IN FROM ANT.				both scrambled		other than
								the one
		R				and
	IN OUT	L VHF/UHF				unscrambled		selected for
						channels if		any type of
		VIDEO	OUT TO TV			additional		recording.
					TV
		IN 1 OUT				equipment is	•	do a Timer
ANT				IN	OUT	added.
or	2-Way Splitter		A/B Switch			This connection		recording of
		CABLE BOX		R	AUDIO	requires: two		a channel
CATV		IN OUT	IN 1 IN 2	L		converter		unless you
	OUT 1 OUT 2				VIDEO	boxes, an A/B		select it at
					VHF/UHF	switch, and a 2-		the cable
						way splitter.		box.

SAP broadcast	STOP 12 : 0 0AM	CH 02
Secondary Audio Program (sub language) broadcast.	STEREO	0 : 00 : 00
Select SAP audio mode for the sub language.		SP
	SAP

MONO

MONO broadcast	STOP	12 : 0 0AM CH 02
Normal monaural sound broadcast.	STEREO	0 : 00 : 00
		SP
	SAP
	MONO

Equipped with ®-TV Noise Reduction for true MTS reproduction. ®-TV Noise Reduction is required for good stereo separation and audio fidelity. ® is a registered trademark, and is licensed by ® Technology Licensing.

•Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound.

•To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amp and speakers. (See page 4.)

•If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

•Hi-Fi and normal audio playback volume level may differ.

*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.

NOTE: indicates start points of each recording.

Note

•If Index Search is started very close to an index mark, that index mark may not be counted in the search.

skipped over.

• To cancel, press PLAY or STOP.

If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.

- 2 - - 3 - - 4 - - 5 - - 6 - - 7 -