Assembly Instructions
Placement
STEP 1 Plasma TV installation and fastening method
∗Install the plasma TV by referring to the following illustration.
∗Do not hold the plasma TV at the bottom of the front panel.
1.Align the support pole insertion holes of the plasma TV with the support poles 
(1 each), and lower the plasma TV until the poles stop. Slightly lift the left and right sides of the plasma TV and remove the corner protection pads attached to the bottom.
2.Fasten the plasma TV and support poles 
using assembly screws (black screws) 
(⋅ 4)
TY-S50PX20U
Display stand
The tools required:
Plus (Phillips) (+) screwdriver
IMPORTANT
A study of the assembly instructions will not only save you time, but may prevent possible damage to your new stand.
Assistance may be required for some assembly procedures.
∗Position by placing your hands at the points indicated in the illustration.
Support pole insertion hole
Lift and |
|
remove |
|
Support pole | Corner |
protection pad | |
(Left) |
|
Assembly screws | |
(Black screws) | |
Support pole (Right) | |
CAUTION : THIS STAND IS DESIGNED ONLY FOR USE WITH A PANASONIC PLASMA TV.
APPLIED MODEL :
Use with other appliances may result in instability causing possible injury.
Your hardware pack contains / Replacement parts
Assembly screws | Glass shelf fastening screws | Glass shelf support fastening | ||
|
| screws (Black screws) | ( ⋅ | 4) |
THEA118 ⋅ 4 | THEA102N ⋅ 8 | Rear cord cover fastening |
| |
screws (Black screws) | ( ⋅ | 3) | ||
Support pole fastening screws | Assembly screws (Black screws) |
|
|
|
XST5+12 ⋅ 4 | XYN5+F55FZ ⋅ 4 | XSB4+12FZ ⋅ 7 |
|
|
Support pole (Right) | Support pole (Left) | Cord clamps |
|
|
TBLA3196 ⋅ 1 | TBLA3197 ⋅ 1 | TBLB3111 ⋅ 6 |
|
|
Glass shelf supports (Right) | Glass shelf supports (Left) | Casters (Wheels) |
|
|
TBLA3194 ⋅ 2 | TBLA3195 ⋅ 2 | TBLB3074 ⋅ 4 |
|
|
Replacement parts |
|
|
|
|
Bottom cap (Right) | Bottom cap (Left) | Screws |
|
|
TBLB3107 ⋅ 1 | TBLB3108 ⋅ 1 | XTB4+10B ⋅ 4 |
|
|
|
To maintain appearance we recommend the following:
Painted Surfaces:Use a damp cloth for cleaning. Do not use any abrasive or chemically treated cleaners. NOTE: As with all indoor furniture, this unit should not be exposed to direct sunlight, extreme temperatures or moisture, as this can result in serious irreparable damage.
For improvement purposes, design and specifications are subject to change without notice.
STEP 2 To use with equipment such as a video deck
∗ Wire over the minimum distance
•To thread wiring, remove the terminal cover and pass wires along the grooves in the rear cord cover, along the groves in the left and right
side panels, and along the groves in the cord holder under the glass |
|
|
shelf. |
|
|
∗ Some equipment may have short cords. In such an instance, thread | (Back) |
|
the wiring over the minimum distance, as indicated by the dotted line in |
| |
|
| |
the diagram. |
|
|
• After threading wiring, fasten with cord clamps (⋅ 6) so that the cords |
|
|
do not protrude from the grooves. Finally, attach the terminal cover. |
|
|
If there are any cord clamps left over, store them carefully. You will |
|
|
need them if you use the unit to house more equipment in the future. |
|
|
∗ The top glass shelf is specifically for the center speaker and AV | Cord clamps |
|
amp. If you place a video deck here, it may badly affect the picture. | Power cord |
REPLACEMENT PARTS LIST
|
| ||
Ref. Description | Qty. Part No. | Part No. | |
Top crosspiece | 1 | TBLA0116 | TBLA0117 |
Bottom panel | 1 | TBLH0548 | TBLH0550 |
Side panel (Left) | 1 | TBLA0104 | TBLA0104 |
Side panel (Right) | 1 | TBLA0103 | TBLA0103 |
Rear cord cover | 1 | TBLB3080 | TBLB3110 |
Glass shelf | 1 | TKGA0127 | TKGA0129 |
Cord holder | 1 | TBLA3184 | TBLA3217 |
When making a part (s) inquiry or for out of warranty purchases please quote part no. & description.
PANASONIC SERVICES COMPANY
20421 84th Avenue South, Kent, Washington 98032 | Tel. : | Fax : |
2003 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3Tel. : (905)
2003 Matsushita Electric Industeial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
TQZH507 Printed in Japan
