Specifications
g AMPLIFIER SECTION RMS Output Power
Front Ch (both ch driven) 20 W per channel (6 Ω), 1 kHz, 10 % THD
Total RMS power |
| 40 W |
Phone jack |
|
|
Terminal |
| Stereo, 3.5 mm jack |
Output level (CD, 1 kHz, | max. 0.2 mW + 0.2 mW, 32 Ω | |
Aux (Rear) |
|
|
Terminal |
| Stereo, 3.5 mm jack |
g TUNER SECTION |
|
|
Preset Memory |
| FM 30 stations |
|
| AM 15 stations |
Frequency Modulation (FM) |
|
|
Frequency range | 87.50 MHz to 108.00 MHz (50 kHz step) | |
Antenna terminals |
| 75 Ω (unbalanced) |
Amplitude Modulation (AM) |
|
|
Frequency range |
| 522 kHz to 1629 kHz (9 kHz step) |
|
| 520 kHz to 1630 kHz (10 kHz step) |
g DISC SECTION
Disc played [8 cm or 12 cm]
(1)
(2)
(3)MP3*
*
Pick up
Wavelength |
|
| 795 nm |
Laser power |
|
| CLASS 1 |
Audio Output (Disc) |
|
|
|
Number of channels |
|
| FL, FR, 2 channel |
g SPEAKER SECTION |
|
|
|
Type | 1 way, 1 speaker system (Passive Radiator) | ||
Speaker unit(s) |
|
|
|
Full range |
|
| 6.5 cm Cone type x 1 / channel |
Passive Radiator |
|
| 8 cm x 2 / channel |
Impedance |
|
| 6 Ω |
g GENERAL |
|
|
|
Power supply |
|
| AC 220 V to 240 V, 50 Hz |
Power consumption |
|
| 31 W |
Dimensions (W x H x D) |
|
| 500 mm x 201 mm x 102 mm |
|
|
| (D = 69 mm minimum) |
Mass |
|
| Approx. 2.8 kg |
Operating temperature range |
| 0 °C to +40 °C | |
Operating humidity range |
| 35 % to 80 % RH (no condensation) | |
|
| ||
Power consumption in standby mode: | 0.09 W (approx.) | ||
|
|
|
|
•Specifications are subject to change without notice.
•Total harmonic distortion is measured by the digital spectrum analyser.
Safety precautions
Placement
Set the unit up on an even surface away from direct sunlight, high temperatures, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the unit’s service life.
Do not place heavy items on the unit.
Voltage
Do not use high voltage power sources. This can overload the unit and cause a fire.
Do not use a DC power source. Check the source carefully when setting the unit up on a ship or other place where DC is used.
AC mains lead protection
Ensure the AC mains lead is connected correctly and not damaged. Poor connection and lead damage can cause fire or electric shock. Do not pull, bend, or place heavy items on the lead.
Grasp the plug firmly when unplugging the lead. Pulling the AC mains lead can cause electric shock.
Do not handle the plug with wet hands. This can cause electric shock.
Foreign matter
Do not let metal objects fall inside the unit. This can cause electric shock or malfunction.
Do not let liquids get into the unit. This can cause electric shock or malfunction. If this occurs, immediately disconnect the unit from the AC mains supply and contact your dealer.
Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit.
Service
Do not attempt to repair this unit by yourself. If sound is interrupted, indicators fail to light, smoke appears, or any other problem that is not covered in these instructions occurs, disconnect the AC mains lead and contact your dealer or an authorized service centre. Electric shock or damage to the unit can occur if the unit is repaired, disassembled or reconstructed by unqualified persons.
Extend operating life by disconnecting the unit from the AC mains if it is not to be used for a long time.
RQTX1073
15