Anti-Skip System
≥The thinner and lighter construction makes the unit less susceptible to vibration.
≥An
≥A recovery system immediately returns the laser pick- up to its original position if it is knocked off the track by a strong shock.
≥The
Press during play or stop mode.
A.SKIP
G
The following indicator appears on the display panel.
After about | About |
20 seconds | 5 seconds later |
Note!
Wait until the jogger indicator appears before starting to jog.
When bumps continue repeatedly
The message “SORRY” appears on the display and sound is interrupted.
A.SKIP
The jogger indicator can also flash or go out under the following conditions:
≥As the end of the last track approaches.
≥As the end of a track approaches during random play, pro- gram play, and 1 track repeat play.
≥If the track in play or next track is extremely short.
Note!
≥The
≥During
Listening to sound with the unit con- nected to an audio system
The
To cancel the anti-skip function
A.SKIP | A.SKIP | A.SKIP | Press [A.SKIP] again. |
|
|
|
The jogger indicator starts flashing.
Using Stereo Headphones with Remote Control
SL-SW895 ONLY
The remote control can be operated regardless of the HOLD mode of the unit.
Preparation: Release the remote control from the HOLD mode.
Play/stop/off button |
|
[j] | [i] |
VOL |
|
HOLD | |
[VOL] | HOLD |
∫Operation confirmation tones
When an operation button is pressed, a confirmation tone sounds. Refer to the parentheses in the illustra- tion for the different types of confirmation tones.
How to use the remote control
Press once during off or stop mode. (Beep)
To start play
VOL
HOLD
Press once during play. (Beep...Beep)
To stop play
VOL
HOLD
Press and hold during play or stop mode. (Beep...Bee...p)
To turn off |
|
the unit | VOL |
HOLD
| Press once during play. |
|
Skipping | Backward | Forward |
tracks | (Beep Beep | (Beep |
| Beep) | Beep) |
| VOL |
|
| HOLD |
|
Searching
through tracks
Press and hold during play.
VOL
HOLD
To adjust the
volume
[VOL] on the remote control adjusts volume only. To adjust the VMSS effect, use [VOLUME] on the main unit.
Using the Unit with Optional Accessories
Maintaining the Lens
5
Using a stereo connection cable (not included), you can listen to CDs through your audio system.
≥Connect the cable to the amplifier after turning off its power.
≥Do not connect the cable to the PHONO jacks on the amplifier.
≥Obtain the optional connecting cable if the amplifier comes with
≥Adjust the volume level on the amplifier.
You can connect speakers, active or otherwise, with an impedance of 1k≠ or less to the headphone jack. Set the unit’s volume between 5 and 8.
Note.
Sound quality changes when
OUT jack
Side panel of the unit
Amplifier
(White) L To CD or AUX
terminals (Red) R
Stereo connection cable (not included)
Items to be purchased (SL-SW895/SL-SW890)
For connection to the car audio system:
Car stereo cassette adaptor
Connect the car stereo cassette adaptor to the unit’s headphone jack.
(When doing this, keep the unit’s VOLUME control at a setting between 5 and 8.)
For securing the unit and connecting the power supply:
≥Car adaptor
≥Car mounting kit
Note.
It may not be possible to use the unit with some types of car stereo owing to restrictions imposed by the con- struction of the car stereo cassette adaptor.
For further details, refer to the instructions of the part concerned.
Open the lid and clean the lens as shown in the figure. Use a cotton swab to gently wipe off any
Air blower for camera lens
Lens
Lens
To prevent the disc from being scratched or damaged
Remove built up dust from the felt pads.
Felt pads
RQT5963