Options Adjustments

Item

 

 

 

Adjustments

Off

PC

INPUT1

INPUT2

INPUT3

Locks the input switch operation.

 

Notes:

 

 

 

 

•Only the adjusted signal is displayed (see page 13).

•Signal can be displayed when the Terminal board is installed.

INPUT lock

• Input switch can be used when this is set to “Off”.

 

 

 

 

 

 

 

 

• In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value input in

 

the single screen display mode.

 

 

 

 

 

• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal.

 

(Ex. INPUT1A, INPUT1B)

 

 

 

 

 

 

Off

MENU&ENTER

On

 

 

 

 

 

Off: All the buttons on main unit can be used.

 

 

 

 

MENU&ENTER: Locks MENU

and ENTER/■ buttons on main unit.

 

 

Button lock

On: Locks all the button on main unit.

 

 

 

 

Sets Button lock with the unit buttons in the following procedure.

 

 

 

 

Off: Press +/▲ four times

Press INPUT

four times

Press –/▼

four times

Press ENTER/■

 

MENU&ENTER: Press ENTER/■ four times

Press +/▲

four times

Press INPUT

four times Press ENTER/■

 

On: Press –/▼four times

Press ENTER/■

four times

Press +/▲

four times

Press ENTER/■

Off

User1

User2

User3

 

Off:

You can use all of the buttons on the remote control.

Remocon User level User1:You can only use

, ,

, , ,

buttons on the remote control.

User2:You can only use button on the remote control.

User3:Locks all the buttons on remote control.

 

Off:

Sets normal two screen display mode (see page 17).

 

On:

Sets Advanced PIP mode (see page 18).

Advanced PIP

Notes:

 

 

 

 

 

• When “INPUT lock” is “On”, you cannot use all the two screen display functions.

 

• ,

buttons are unavailable during Advanced PIP mode operation.

 

 

 

Enable: Enables the “Off-timer function”.

Off-timer function

Disable:

Disables the “Off-timer function”.

 

Note:

 

When “Disable” is set, the Off-timer is cancelled.

 

Normal

Standby

On

 

Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.

Initial Power Mode

Normal: Power returns in as the same state as before the power interruption.

Standby: Power returns in standby mode. (Power Indicator : red/orange)

 

 

On:

 

Power returns in power On. (Power Indicator : green)

 

Note:

 

When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.

 

Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.

ID select

Set value range: 0 - 100

 

 

(Standard value: 0)

 

 

 

The setting of this menu is valid only when using ID remote control.

Remote ID

Off:

Disables ID remote control functions. You can use normal remote control operations.

 

On:

Enable ID remote control functions.

 

Sets the panel ID Control.

 

Serial ID

Off:

Disables external control by the ID.

 

On:

Enables the external control by the ID.

 

Off

 

Auto

On

 

 

Off:

Power is not transmitted to the slot power.

Slot Power

Auto: Power is transmitted to the slot power only when main power is on.

On:

Power is transmitted to the slot power when main power is on or in the standby state.

 

 

Note: In some cases, power is transmitted to the slot power when main power is on or in the standby state

 

 

regardless of the slot power setting.

35