qAlarm Indicator (ALARM)
Blinks to indicate that an alarm condition exists.
It changes to steady light when the alarm is reset auto- matically.
To turn the indicator off, press the ACK RESET button.
wBusy Indicator (BUSY)
Lights up when you attempt to control a monitor or a camera that is already used by a higher priority opera- tor, or when the higher priority operator selects the monitor or camera you are currently operating.
Operations from the System Controller are disabled until this indicator goes off.
eFunction Buttons (F1/F2/F3/F4)
Select functions displayed on the LCD (Liquid Crystal Display) display.
rLCD (Liquid Crystal Display) Display
Displays function menus, numeric input, and system status.
tDirection Buttons (4, 5, i, o)
Select a function menu for display on the LCD display.
yJoystick Controller (UP/DOWN/LEFT/RIGHT)
The joystick is used to manually operate the Pan/Tilt Head, or move the cursor in the Matrix Switcher’s Setup Menu on the active monitor screen.
To control the Pan/Tilt functions of the Combination Camera slowers, press the ALT button (ALT indicator lights) before operating the joystick.
uIris Control Buttons (IRIS CLOSE, OPEN)
Close or open the lens iris of cameras equipped with the specified lens.
When these buttons are pressed at the sometime for 3 seconds or more, the lens iris is reset to the factory default setting.
iFocus Control (FOCUS NEAR/FAR)
Adjust the lens focus of cameras equipped with the specified lens.
oZoom Control (ZOOM TELE/WIDE)
This control is used for zooming cameras equipped with the specified lens.
!0Preset Button (PRESET)
Auto Focus Button (AF)
PRESET: This button, in combination with the Numeric keys, is used to move the selected camera to a pre- set position in a system equipped with the specified cameras.
AF: Pressing this button will automatically set the lens focus of a specified camera such as the
!1Camera (Set) Key [CAM (SET)]
CAM: Used for camera selection. To select a camera, enter the desired camera number with the Numeric keys, and then press the CAM key.
SET: This key, in combination with the Numeric keys, is used to enter numeric input, such as operator ID and password.
It is also used to execute the currently highlighted selection and to enter a submenu in the Setup Menu of the Matrix Switcher.
!2Numeric Keys (0 - 9)
These keys are used for numeric input into the system, such as the camera and monitor number, sequence number, preset position, etc.
!3Monitor (Escape) Key [MON (ESC)]
MON: This key is used to select a monitor.
To select a monitor, press the corresponding Numeric keys, followed by the MON key.
ESC: This key is used to escape from the currently highlighted selection on the Setup Menu of the Matrix Switcher.
Pressing this key, while the Alternate (ALT) indicator is on, will display the video that is connected to the Monitor Input (MONITOR IN) Connector on the WV- PB5504 Video Output Board.
!4Stop/Slow Button (STOP/SLOW)
STOP: Pauses a sequence that is being run on the active monitor.
SLOW: For fine pan/tilt control, move the joystick while holding down the SLOW button.
!5Increment Button (INC +1CAM)
When a sequence running in forward direction has been paused with the Stop button, pressing this button will move the sequence one frame to the next step (in forward run direction). If the sequence was running in reverse direction, the button will move the sequence one frame to the next step (in reverse run direction).
This button is also used to select a camera. Pressing this button will replace the currently selected camera with the next higher camera number, if the active moni- tor is in Spot mode.
!6Decrement Button (DEC
When a sequence running in forward direction has been paused with the Stop button, pressing this button will move the sequence one frame to the previous step (in forward run direction). If the sequence was running in reverse direction, the button will move the sequence one frame to the previous step (in reverse run direc- tion).
This button is also used to select a camera. Pressing this button will replace the currently selected camera with the next lower camera number, if the active monitor is in Spot mode.
7
