ParaBody 8661O2 manual Upright Frame, WASHERS. Make Sure Both Hinge Tabs are ALL the Wayon the PIN

Insert one (1) 3 X2 IN. ENDCAPinto the top of the UPRIGHTFRAME,and two (2) 2 EN. SQ. CAPSinto the BASEof the UPRIGHTFRAMEas shown on drawing. Repeat this step for the second

UPRIGHT FRAME.

SECURELYassemble both UPRIGHTFRAMESto the CROSSBRACEas shown on drawing using four (4) 1/2 X 3 IN. BOLTS,four (43 1/2 IN. WASHERS,and four (4) 1/2 IN. LOCKNUTS;.

(IMPORTANT: THE ANGLE BRACKETS ON THE CROSS BRACE ARE OFFSET, PLEASE MAKE SURE THAT THE LONGEST END OF THE BRACKET IS FACING UP BEFORE ASSEMBLY)

SECURELYassemble the BENCHFRAMEto the CROSSBRACEas shown on drawing using two (2) 1/2 X 3 IN. BOLTS,two (2) 1/2 IN. WASHERS,and two (2) I/2 IN. LOCKNUTs.Attach one 2" cover cap to the BENCHFRAMEas shown.

Insert two (2) 1/2 IN. FLANGEBEARINGSinto each end of the BUSHINGof the BENCttFRAME shown on drawing.

SECURELYassemble the BENCHSLIDE to the BUSHINGof the BENCHFRAMEas ~hown on drawing, using one (1) 1/2 X 3-1/2 IN. BOLTone (1) 1/2 IN. LOWHTLOCK

Attach eight (8) 1-1/2 X 3/4" GLIDESto the WOLFFSLEEVE(FOURONEACHEND)as shown (DETAILA) using the following steps:

Thoroughlyclean all surfaces wherethe GLIDESare to be attac1~ed.

Removethe GLIDESfrom the paper backing and firmly apply them to all shownsurfaces.

Insert one (1) U-PINthrough the BUSHINGof the WOLFFSLEEVEas.shown on drawing, and attach one (I) PALNUTto the end of the U-PIN.

SECURELYAssemble one (1) SPRINGPIN ASSEMBLYto the SPRINGPIN BARREL,of the WOLFFSLEEVEas shown in (DETAIL B). (!!! IMPORTANT!!! TIG~ITEN THE NUTOF SPRING PIN ASSEMBLYSECURELY)

Pull back the SPRINGPIN on the WOLFFSLEEVEand slide it over the end of the BENCHSLIDEas shown on drawing. Engage the SPRINGPIN into one of the adjustment holes. Secure the WOLFF SLEEVEin place with one (1) 3-PRONGKNOB.

I0. LOOSELYassemble one (1) 3 PRONGKNOBto the UPRIGHTTUBEof the BENCHFRAME shown on drawing. (THIS WILL BE USED TO SECUREATTACHMENTSIN PLACE)

11.Attach one (1) 1-1/4 IN. S Q. RUBBERBUMPERto the SLIDESUPPORTas shown on drawing.

12.SECURELYassemble the SLIDE SUPPORTto the end of the BENCHSLIDEas shown on drawing using one (I) 3/8 X2-3/4 IN. BOLT,two (2) 3/8 IN WASHERS,and one (1) 3/8 IN. LOCK

13.Attach two (2) 1 X 1 GLIDESto the top of the BENCHFRAMEwhere the SLIDESUPPORTmakes contact. See drawing.

14.Assemble the SEATPADto the WOLFFSLEEVE,start by sliding two(2) HINGETABSover the PIN of the WOLFFSLEEVE(ONE ONEACHSIDE) as shown on drawing, and SECURELYassemble each HINGETABto the SEATPADusing two (2) 3/8 X 1-1/4 IN. BOLTSand two (2) 3/8

WASHERS. (MAKE SURE BOTH HINGE TABS ARE ALL THE WAYON THE PIN)

Part # 6611901 3 Revision: 04/30/96