Paradyne 3162 DSU/CSU SNMP NMS Security Configuration Options

Configuration Options

C-30 3162-A2-GB20-30March 1999

SNMP NMS Security Configuration Options

Table C-14. SNMP NMS Security Configuration Options

NMS IP Validation: Disable

Enable Disable

Specifies whether the DSU/CSU validates (for security reasons) the IP address of an

SNMP manager attempting to access the DSU/CSU. Allowable addresses are specified

using the NMS

n

IP Adr configuration option.

Enable – The DSU/CSU validates the IP address of SNMP managers attempting to

access the DSU/CSU.

Disable – The DSU/CSU does not validate the IP address of SNMP managers.

Number of Managers: 1

1 2 3 4 5 6 7 8 9 10

Specifies the number of SNMP managers that are allowed to access the DSU/CSU.

NOTE: You must configure an IP address for each SNMP manager that is allowed

access to the DSU/CSU. Allowable addresses are specified using the NMS

n

IP Adr configuration option.

NMS

n

IP Address:

Text Field

Text Field

Clear

Specifies the allowable IP address of an SNMP manager attempting to access the

DSU/CSU. The manager number (

n

) is specified by the Number of Managers

configuration option.

Text Field

– Allows you to edit or display the allowable IP address for the SNMP

manager.

Clear – Allows you to clear the allowable IP address for the SNMP manager. The IP

address is set to 000.000.000.000.

Access Level: Read

Read Read/Write

Specifies the allowable type of access for an authorized SNMP manager if IP address

validation has occurred.

Read – Allows read-only access (SNMP Get) to the accessible objects in the MIB for

this device. This includes all objects specified as either read-only or read/write in the

MIB RFCs.

Read/Write – Allows read and write access (SNMP Get and Set) to the objects in the

MIB for this device. Write access is allowed for all objects specified as read/write in the

MIB RFCs. Read access is allowed for all objects specified as either read-only or

read/write.

Contents

Main Page B !Important Safety Instructions Page D Government Requirements and Equipment Return United States NOTICE TO USERS OF THE UNITED STATES TELEPHONE NETWORK DSU/CSU Facility Interface Codes Code Description Caution: i Contents About This Guide 1 Introduction 2 Installation ii 3 Operation iii 4 Monitoring and Testing iv A Asynchronous Terminal Menu B Technical Specifications C Configuration Options D Pin Assignments v E SNMP MIB Objects F IP Network Addressing Scenario G Equipment List Glossary Index Page vii About This Guide Document Purpose and Intended Audience Document Summary Section Description viii Product-Related Documents Document Number Document Title Reference Documents 1-1 Introduction 1 Features 1-2 DTE Drop/Insert (DSX-1) Interface Operation Asynchronous Terminal Interface Support Alarm Message Capability Telnet Access Physical Description Test Jacks Operation Front Panel LEDs 1-4 2-1 Installation 2 Application Examples 2-2 NETWORK SERVICES Figure 2-3. Fractional T1 Application Example Figure 2-2. Shared Access Application Example FRACTIONAL NETWORK SNMP or Telnet Connection Examples NETWORK 2-4 NETWORK Figure 2-8. Remote Access through FDL/EDL NETWORK Figure 2-6. Connection through a LAN Adapter Important Instructions Figure 2-9. Cabling Examples Pin Assignments Important Safety Instructions section at the beginning of this guide. Power-Up Self-Test Self-Test Results Maintenance 3-1 Operation 3 Menu Organization Front Panel LEDs 3-2 Table 3-1. System LEDs Table 3-2. Network Interface LEDs 3-3 Table 3-3. DTE Drop/Insert (DSX-1) Interface LEDs 3-4 Table 3-4. Data Port LEDs 3-5 Initiating an Asynchronous Terminal Session Entering a Password to Gain Access Ending an Asynchronous Terminal Session 3-6 Recovering Asynchronous Terminal Operation 3-7 3162-A2-GB20-30 March 1999 Menu Organization Figure 3-3. Menu Organization Figure 3-3 shows the organization of the asynchronous terminal menu tree. 3-8 Using Asynchronous Terminal Screens 3-9 3-10 Setting Customer Identification 3-11 Displaying LED Conditions 3-12 Changing Configuration Options 3-13 Displaying or Editing Configuration Options 3-14 Figure 3-7. Configuration Edit/Display Screen 3-15 Saving Edit Changes 3-16 Configuring the DSU/CSU for SNMP or Telnet Access Configuration Examples 3-17 Selecting the Port 3-18 Setting the IP Address xxx.xxx.xxx.xxx IP Network Addressing Scenario 3-19 Selecting the Link Layer Protocol Setting the IP Address Selecting the Port 3-20 Configuring DS0 Channels 3-21 Figure 3-10. Example of Channel Allocation 3-22 Network Interface Network Channel Allocation Figure 3-11. Example of Network Interface Worksheet 3-23 DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation Figure 3-12. Example of DTE Drop/Insert Interface Worksheet 3-24 Displaying DS0 Channel Assignments 3-25 3-26 Allocating DS0 Channels from the DTE Drop/Insert Interface to the Network Interface 3-27 Configuring DS0 Channels for Robbed Bit Signaling 3-28 Allocating Data Ports Using the Block or ACAMI Assignment Method n 3-29 Allocating Data Ports Using the Individual Channel Assignment Method Clearing DS0 Channel Allocation 3-30 Establishing Access Security on a Port Setting a Password 3-31 Setting a Password Establishing Access Security on a Port 3-32 Entering a Password to Gain Access If an invalid password is entered three consecutive times If the password is invalid If the password is valid Selecting the Timing Source 3-34 Providing Backup Capability Download Operations 4-1 Monitoring and Testing 4 Installation Self-Test Results 4-2 Table 4-1. Self-Test Results xxxxxxxx 4-3 Device Health and Status To display health and status messages: 4-4 Performance Reports 4-5 To display performance reports: 4-6 Table 4-3. Performance Registers (2 of 3) Register Totals DescriptionInterval Description 4-7 Table 4-3. Performance Registers (3 of 3) Register Totals DescriptionInterval Description 4-8 Alarms 4-9 Alarm and Trap Troubleshooting SNMP Traps 4-10 4-11 Troubleshooting 4-12 Table 4-6. Troubleshooting (2 of 2) Symptom SolutionsPossible Cause 4-13 Test Jacks 4-14 Test Commands 4-15 Remote Loopback Tests For Networks For Channels Sending a Line Loopback Up or Down 4-16 Local Loopback Tests 4-17 Starting a Line Loopback 4-18 Starting a Payload Loopback Starting a DTE Loopback 4-19 Starting a Repeater Loopback 4-20 Starting a Data Channel Loopback 4-21 Starting a Data Terminal Loopback Aborting Loopbacks 4-22 Test Patterns Sending Network QRSS or Network 1-in-8 Test Patterns Page Lamp Test 4-25 Displaying DSU/CSU Test Status To display test status: 2. From the Status screen, select System and Test Status. Table 4-10. Test Status Messages Page A-1 Asynchronous Terminal Menu A Page B-1 Technical Specifications B Technical Specifications B-2 Table B-1. Model 3162 DSU/CSU Technical Specifications (2 of 2) Specifications Criteria C-1 Configuration Options C C-2 Network Interface Configuration Options Table C-1. Network Interface Configuration Options (1 of 3) C-3 Table C-1. Network Interface Configuration Options (2 of 3) C-4 Table C-1. Network Interface Configuration Options (3 of 3) DTE Interface Configuration Options Table C-2. DTE Interface Configuration Options (1 of 2) C-5 Table C-2. DTE Interface Configuration Options (2 of 2) C-6 Sync Data Port Configuration Options Table C-3. Sync Data Port Configuration Options (1 of 5) C-7 Table C-3. Sync Data Port Configuration Options (2 of 5) C-8 Table C-3. Sync Data Port Configuration Options (3 of 5) C-9 Table C-3. Sync Data Port Configuration Options (4 of 5) C-10 Table C-3. Sync Data Port Configuration Options (5 of 5) C-11 Cross Connect Configuration Options DTE-to-Network Assignment Options Table C-4. DTE-to-Network Assignment Options C-12 Sync Data Port Assignment Options Table C-5. Sync Data Port Assignment Options (1 of 3) C-13 Table C-5. Sync Data Port Assignment Options (2 of 3) OR C-14 Table C-5. Sync Data Port Assignment Options (3 of 3) C-15 General Configuration Options Table C-6. General Configuration Options (1 of 2) C-16 Table C-6. General Configuration Options (2 of 2) C-17 User Interface Configuration Options Communication Port Configuration Options C-18 Table C-7. Communication Port Configuration Options (2 of 3) C-19 Table C-7. Communication Port Configuration Options (3 of 3) External Device Configuration Options Table C-8. External Device Configuration Options (1 of 3) C-20 Table C-8. External Device Configuration Options (2 of 3) C-21 Table C-8. External Device Configuration Options (3 of 3) X.X C-22 Telnet Sessions Configuration Options Table C-9. Telnet Sessions Configuration Options C-23 Auxiliary Port Configuration Options Table C-10. Auxiliary Port Configuration Options C-24 Alarm and Trap Configuration Options Table C-11. Alarm and Trap Configuration Options (1 of 2) C-25 Table C-11. Alarm and Trap Configuration Options (2 of 2) C-26 Management and Communication Configuration Options Communication Protocol Configuration Options C-27 Table C-12. Communication Protocol Configuration Options (2 of 3) C-28 Table C-12. Communication Protocol Configuration Options (3 of 3) C-29 General SNMP Management Configuration Options Table C-13. General SNMP Management Configuration Options C-30 SNMP NMS Security Configuration Options Table C-14. SNMP NMS Security Configuration Options C-31 SNMP Traps Configuration Options Table C-15. SNMP Traps Configuration Options (1 of 3) C-32 Table C-15. SNMP Traps Configuration Options (2 of 3) C-33 Table C-15. SNMP Traps Configuration Options (3 of 3) C-34 Configuration Worksheets C-35 Sync Data Port Options (Port 1) Value (Default in Bold) C-36 Sync Data Port Options (Port 2) Value (Default in Bold) C-37 Network Interface Network Channel Allocation C-38 DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation C-39 DTE Signaling Assign: (N1 24) Voice RBS or Data) C-40 Sync Data Port Channel Options Value (Default in Bold) C-41 General Options Value (Default in Bold) User Interface: Communication Port Options Value (Default in Bold) User Interface: External Device Options Value (Default in Bold) C-42 C-43 Communication Protocol Options Value (Default in Bold) General SNMP Management Options Value (Default in Bold) SNMP NMS Security Options Value (Default in Bold) C-44 D-1 Pin Assignments D Equipment List T1 Network Interface Page D-3 DTE Drop/Insert Interface DTE Interface Configuration Options D-4 AUX Port Interface D-5 COM Port Interface Page D-7 EIA-530-A Port Interface Connector D-8 EIA-530-A-to-RS449 Adapter Figure D-6. EIA-530-A-to-RS449 Adapter The EIA-530-A-to-RS449 adapter (Figure D-6) provides the RS449 interface shown in Table D-6. D-9 Table D-6. RS449 Cable Interface Signal Circuit Mnemonic CCITT D-10 EIA-530-A-to-V.35 Adapter Figure D-7. EIA-530-A-to-V.35 Adapter The EIA-530-A-to-V.35 adapter (Figure D-7) provides the V.35 interface shown in Table D-7. D-11 Table D-7. V.35 Cable Interface Signal CCITT D-12 EIA-530-A-to-X.21 Adapter The EIA-530-A-to-X.21 adapter (Figure D-8) provides the X.21 interface shown in Table D-8. Figure D-8. EIA-530-A-to-X.21 Adapter Table D-8. X.21 Cable Interface Signal CCITT D-13 Serial Crossover Cable Figure D-9. Serial Crossover Cable D-14 External Clock Interface E-1 SNMP MIB Objects E MIB II (RFC 1213) E-2 System Group, MIB II Company OID ssssssss zzzz-zzz yy.yy.yy Interface Group, MIB II E-4 n E-5 E-6 E-7 IP Group, MIB II E-8 E-9 E-10 ICMP Group, MIB II TCP Group, MIB II UDP Group, MIB II E-11 Transmission Group, MIB II DS1/E1 MIB (RFC 1406) E-12 Near End Group, DS1/E1 MIB E-13 E-14 E-15 E-16 Far End Group, DS1/E1 MIB DS1 Fractional Group, DS1/E1 MIB E-17 RS-232-like MIB (RFC 1317) General Port Table, RS-232-like MIB E-18 E-19 Asynchronous Port Table, RS-232-like MIB E-20 Synchronous Port Table, RS-232-like MIB Input Signal Table, RS-232-like MIB E-21 Output Signal Table, RS-232-like MIB Generic-Interface MIB Extensions (RFC 1229) E-22 Generic Interface Test Table, Generic Interface MIB E-23 E-24 Enterprise MIB F-1 IP Network Addressing Scenario F IP Network Addressing F-2 G-1 Equipment List G Equipment Feature Number Page GL-1 Glossary GL-2 GL-3 GL-4 GL-5 GL-6 GL-7 GL-8 GL-9 Page IN-1 Index A B C IN-2 D E F I IN-3 L M N O IN-4 P Q R S IN-5 T U V W X