Paradyne 1020 warranty USB Po rt, Pow e rLED, T rans fe rLED, E the rne tPo rt, s G u die, from

s G u die Insta lal

TM

DSLM odem
	T
R M PSOT R

FCC Compliance Information

Federal Communications Commission

Compliance Information Statement (FCC Rules Section 2.1077) 2.1077 (a) (1) Product identification

Name: StormPort 620 Modem, Product code: 02-00079-03

Name: StormPort 1020 Modem, Product code: 02-00100-01

2.1007 (C) The compliance information statement shall be included in the user guide or as a separate sheet.

FCC Information to User

2.1077 (a) (2) Compliance Statement	2.1077 (a) (3) Responsible Party (FCC 2.909)
This device complies with part 15 of the FCC rules. Operation is subject	Paradyne Corporation
to the following two conditions:	8545 126th Avenue
a. This device may not cause harmful interference, and	Largo, FL 33773
b. This device must accept any interference receive, including interference	Phone: 727-530-2000
that may cause undesired operation.	www.paradyne.com

(FCC Rules Section 15.105(b)):

Note: The StormPort Modem has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio and television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna

-Increase the separation between the equipment and receiver

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/television technician for help.

Customer Instructions

The Phone Filters comply with part 68 of the FCC Rules. On the back of this equipment is a designator that contains the FCC registration number and ringer equivalence for this equipment. If requested, this information must be provided to the telephone company. The equipment uses the following standard connections and codes: USOC-RJ-11.

The Phone Filters also comply with part 1950 of the UL certifications, and part 22.2 of the CSA certifications.

The Ringer Equivalence Number (REN) shown on the filter is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in another device not ringing in response to an incoming call. The sum of the RENs should not exceed (5). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.

If the equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

The equipment can not be used on public coin phone service provided by the telephone company. Connection to party lines is subject to state tariffs. (contact the state public utility commission, public service commission or corporation commission for information).

No repairs can be performed by the user. If you experience trouble with this equipment and/or for repair and warranty information, please contact distributor technical support.

1020-A2-GN70-10

*1020-A2-GN70-10* Copyright C 2002 Paradyne Corporation. All Rights Reserved.

	USB Po rt
	Th si LED si g reenw hen them odem si rece vi nig pow e r.
	Pow e rLED
the In te rne t.
th si LED	falshes g reenw hen them odem si trans fe rrnig da ta to and	from
si unab el	to "tra ni "w iht the SIP equ pim en t.U nde rnomr a lope ra toin ,
p rocess has com p el ted . The LED w ills tay o ff if them odem
w iht equ pim en ta t the SIP ),and the LED w illchange to g reenw hen		th si
W hen the LED si falsh nig ye lolw , it si “tra ni nig ” (comm un cia tnig
T rans fe rLED
E the rne tPo rt

w a rra nidus N o te :W h iel

lgih nt nig an e elc tr 2 ) D o no tus

ut b ,k itch 1 ) D o no tus

ofyou rm od sa ef ty p reca

When us nig mI po rtan t

The S tomr Po rtM odemoffe rs bo th E the rne tand USB co