XA200.5 Owner’s Manual

The amplifier’s voltage and current rating are indicated on the rear panel. It will be either 240 volts, 230 volts, 220 volts, 120 volts or 100 volts. The larger amplifiers have a circuit breaker of the appropriate capacity. The smaller power amplifiers use a slow- blow 3AG type fuse. The frequency rating of the AC line source is 50 to 60 Hz. Please verify that the amplifiers indicated voltage requirements are consistent with the supplied voltage and current at your location.

On the rear panel you will find both RCA and XLR type input connections for single-ended or balanced inputs. If you use the RCA input, be certain that the XLR connector has a gold shorting plug between pins 1 and 3, which connects the “minus” input to ground, otherwise the amplifier will not operate properly. If you lose this plug, just contact the factory – we give them away all the time.

The question comes up all the time – are balanced inputs (XLR) better than single-ended (RCA)? The answer is that balanced lines generally give lower noise and slightly less distortion. They are recommended unless your favorite source component has only RCA outputs.

Also on the rear panel are the output connections for the loudspeakers. On stereo amplifiers there is one pair per channel, and on mono amplifiers we provide two pairs wired in parallel to facilitate “bi-wiring” a loudspeaker. As you are probably familiar, the red one is positive polarity, and the black one is negative.

Please note that, being a balanced output, both of these terminals are electrically live – neither is grounded and should not be treated as ground. This is particularly important if you are using the output of the amp to also drive a subwoofer amplifier or other active component. If there is any question, please contact the manufacturers of the products involved – both they and we will be happy to advise you.

If you happen to need a clean signal ground connection for any reason, we provide a dedicated 5 way binding post just for that on the rear of the amplifier.

On the rear panel you will also find a pair of 5 way binding posts for external turn-on control. Applying 5 to 12 volts DC at this connection will override the front panel stand-by switch and turn the amplifier on.

6

Page 5 Page 7
Page 6
Image 6
Pass Labs XA200.5 owner manual
Page 5 Page 7

XA200.5 specifications

The Pass Labs XA200.5 is a distinguished power amplifier that epitomizes high-end audio engineering, renowned for its exceptional sound quality and performance. Designed to cater to audiophiles and serious music lovers, the XA200.5 combines innovative technologies with elegant craftsmanship to deliver an unparalleled listening experience.

At the core of the XA200.5 is its Class A topology, which is celebrated for its ability to produce warm, rich sound with minimal distortion. The amplifier is capable of delivering 200 watts of power into an 8-ohm load, and it can double that output for 4-ohm loads, making it suitable for driving a wide range of loudspeakers, from modest bookshelf models to demanding floor-standing designs. This impressive power reserve ensures that the XA200.5 can handle dynamic peaks effortlessly, providing a sense of authority and control over the music.

One of the standout features of the XA200.5 is its proprietary "current source" design. This technology allows the amplifier to deliver musical dynamics with precision while maintaining a linear response across the audio spectrum. Pass Labs emphasizes the importance of low signal distortion, and the XA200.5 achieves this through meticulous engineering, including high-quality components and a robust power supply. The power supply not only supports the high current demands of the amplifier but also contributes to the overall stability and performance of the unit.

The build quality of the XA200.5 is exceptional, with a substantial chassis constructed from high-grade aluminum. This not only adds to its aesthetic appeal but also enhances durability and minimizes resonance, ensuring that the internal components function optimally. The amplifier features a distinctive design with large heat sinks that facilitate efficient thermal management, keeping the unit cool even during extended playback sessions.

Another notable aspect of the XA200.5 is its single-ended input configuration, which is designed to enhance musicality. This input sensitivity allows for direct connection to source components without the need for a preamplifier, ensuring a pure signal path. Additionally, the amplifier includes balanced input options for those who prefer using balanced connections.

In summary, the Pass Labs XA200.5 is a powerhouse of an amplifier that beautifully marries technological innovation and elegant design. With its Class A operation, proprietary current source technology, and exceptional build quality, the XA200.5 delivers a remarkable audio experience that is both impactful and refined, making it a top choice for discerning audiophiles.
Top Page Image Contents